JBL MPC Series User Manual

16
Specifications
Direct Output Models Audio Transformer AND Direct Outputs
Electronics MPC200 MPC300 MPC600 MPC200T MPC300T MPC600T
Direct Power Out
4Ω bridge 1 kHz, 1% THD
1
700 W 900 W 1800 W 700 W 900 W 1800 W
8Ω bridge 45 Hz20 kHz, 1% THD 450 W 600 W 1200 W 450 W 600 W 1200 W
2Ω load/channel
2
, 1 kHz, 1% THD
1
350 W 450 W 900 W 350 W 450 W 900 W
4Ω load/channel
2
, 45 Hz20 kHz, 1% THD 225 W 300 W 600 W 225 W 300 W 600 W
Isolated Constant Voltage Out
200V or 140V Bridge: 350 W 500 W 1000 W
100V or 70V/Channel 175 W 250 W 500 W
25V/Channel: 150 W 200 W 400 W
Frequency Response (bandlimited by built-in highpass filter)
Direct Outputs: 20 Hz20 kHz ±0.2 dB 50 Hz20 kHz* 45 Hz20 kHz**
Isolated Outputs 50 Hz16 kHz* 45 Hz16 kHz**
* -3 dB @ 50 Hz, -0.2 dB @ 20 kHz ** -3 dB @ 45 Hz, -0.2 dB @ 20 kHz
Sensitivity (for full output): 0.96V 1.02V 1.0V 0.96V 1.02V 1.0V
Voltage Gain (direct outputs): 35 (31 dB) 40 (32 dB) 56 (35 dB) 35 (31 dB) 40 (32 dB) 56 (35 dB)
Output Circuit Type: AB AB H AB AB H
AB = Class AB+B complementary linear stage H = Class AB+B linear stage with Class H 2-step high-efficiency circuit
Distortion: SMPTE-IM less than 0.05%
Damping Factor: Greater than 200 (direct outputs)
Noise: Less than 100 dB below rated output (20 Hz to 20 kHz)
Input Impedance: 20k ohm balanced, 10k ohm unbalanced
Amplifier Protection: Short circuit, open circuit, ultrasonic, RF, thermal muting, over-temperature. Stable into reactive or under-impedance loads.
Load Protection: Turn-on / turn-off muting, DC-fault load grounding relay (MPC300, 300T, 600, 600T) with internal fault fuses.
Power Requirements: 100V, 120V, 220230V AC, 5060 Hz (Not user configurable)
Physical:
Controls
Front Panel: Power Switch
Rear Panel: Ch 1 & Ch 2 gain controls (11 detents: 0 dB, -2, -4, -6, -8, -10, -12, -14, -18, -24, off); Parallel/Stereo/Bridge
switch (except MPC200 & 200T)
Connectors Input: Euro-style detachable header with screw-down terminal for bare wires
Output: Covered barrier strip for bare wires or spade terminal
Cooling: Two-speed fan with back-to-front airflow
Net Weight: 14 kg (27 lb) 19 kg (42 lb) 23 kg (50 lb) 18 kg (37 lb) 25 kg (55 lb) 31 kg (67 lb)
Shipping Weight: 17 kg (33 lb) 23 kg (49 lb) 27 kg (58 lb) 21 kg (42 lb) 28 kg (62 lb) 34 kg (75 lb)
Indicators: CLIP: Red
POWER: Green
PROTECT: Red (except MPC200 and 200T)
SIGNAL: Green (except MPC200 and 200T)
Dimensions (H × W × D)
MPC200T & 200: 89 × 483 × 455 mm (rack depth 450 mm); 3.5 × 19 × 17.9 in (rack depth 17.7 in); 2 RU high
MPC300T, 300, 600T, & 600: 133 × 483 × 455 mm (rack depth 450 mm); 5.25 × 19 × 17.9 in (rack depth 17.7 in) 3 Rack Units high
Agency Approvals: UL & CUL approved, CE compliant, and approved by Lucasfilm for THXÒ installations
Optional Accessories: MP-RRB1: Rear Rack Bracket for 3RU (5.25 in) models (set of 2)
MP-RRB2: Rear Rack Bracket for 2RU (3.5 in) models (set of 2)
1
Typical
2
Both channels drive, 120V 60 Hz mains.
JBL continually engages in research related to product improvement. Changes introduced into existing products without notice are an expression of that philosophy.
All manuals and user guides at all-guides.com

JBL MPC Series Specifications

General

Brand	JBL
Model	MPC Series
Category	Amplifier
Language	English