601V-B01A-NB Rev 2-Issue Date 09 2012
3
T6634-TA10҈TE20҈TF20-9JS0 Series Fan Coil Thermostat (ON/OFF) - Installation Instructions
T6634-TA10҈TE20҈TF20-9JS0亨⏄橻㣧䢅䵎㿖㕔⠕ (キ⌠⤸) -ⴶ婲嶡㞻
Up/Down (
Ř
& ) Adjustment Button
To adjust the temperature setpoint, simply pressing the ɘ and button, allows 3-seconds
for setting to take effect. After 3-seconds without further adjustment, the screen returns by
displaying the ambient temperature.
Fan ( ) Speed Button
Cooling or Heating Mode Operation
T6634 has 4 speeds fan control (No Fan Stop); Auto ( ), High ( ), Middle ( ),
Low ( ) fan. Short press the ( ) button switches through the sequence. The selected icon
flashes, the icon is confirmed after 3 seconds. The icon will be displayed on the screen after
confirmed.
Fan only Operation
T6634 has 3 speeds fan control; High ( ), Middle ( ), Low ( ) fan. Short press the
(
) button switches through the sequence. The selected icon flashes, the icon is confirmed
after 3 seconds. The icon will be displayed on the screen after confirmed.
Note:
Every time switch On the T6000 Series thermostat, the low speed fan will be initiated.
These soft-start feature prevent high startup current, while provides energy saving to
electricity consumption. After 2 -seconds, the required fan speed will be started.
ฉ
/
ူ
(
Řࢅ
)
ۙবӀ౧
ݲၫޡົށݞˈᅍՙɘ ՙഀˈ3ಊົᄌȃ3ಊౚ༕ݲˈൺಸ
߬ইმၫޡȃ
ޅ
( )
܈Ӏ౧
ૐĂඤఇ๕֡ፕ
T6634ၫ૿ධ4፯ࠞཨޡˈᏋވ (
), ࡴ ( ), ፩ ( ), ݈ ( ) ࠞཨȃՙ ( ) ՙ
ഀˈᅰმȃ־ᅤܿಠဇດཇˈ3SᏋވฬไဇ־ᅤށȃᅤށဇ
ດཇˈጸ٢მൺಸຢȃ
ৈޅ֡ፕ
T6634ၫ૿ධ3፯ࠞཨޡˈࡴ ( ), ፩ ( ), ݈ ( ) ࠞཨȃՙ ( ) ՙഀˈᅰ
მȃ־ᅤܿಠဇດཇˈ3SᏋވฬไဇ־ᅤށȃᅤށဇດཇˈ
ጸ٢მൺಸຢȃ
ጀᅪ
:
ᇜ۫࣋T6000Ⴜளၫ૿ධˈޕතވ݈ཨࠞȃጝᇜතވ࿅ݞ߷
ፒࣰࡴතވݢˈኙமቂݢˈ2ಊᇵˈࠞՙົށከᎡȃ
1
/Table
1 2
/Table
2
ยֶۨኵ
࣋Ꭻྙՙ
M
/ ঽɘܚ
࠲ڵოˈከᄵد༮ົᎫྙȃՙ
M
/
෧࢙
ˈ
ডɘݲጶყޭሥ࢙ܿد༮ˈ࢙ࣽሆ
2
ȃ
Քۨ
T6000Ⴜளၫ૿ධᅍᇋო٠ށȃ
ࠤቱႪ
ݢኑ፩ިˈၫ૿ධಠྈົইܸᏥቂডົࣰܿᎫྙȃ
ྼႪࢅ༺࣑
ᇋ༅ဇო٠ၕᅃT6000Ⴜளၫ૿ධȃ࣮ၫ૿ධጸ٢ᏮˈขቪࡒJohnson
Controls
®
֑ۃႼȃܬႼ֑ۃٛ൰ܿˈขངಖိؠවডد༮װຢሠ
ܿᄲ/ᄲȃ
ຍ֖ຕ
ขدૣٛ൰ངಖ༚ȃ
Setting Parameter
To enable the operation mode, press the
M
/ and ɘ until icon
appears. When the thermostat
is turned off. Press
M
/
to switch functions between, press or ɘ to adjust the parameter. See
Table
2
for the functions.
Calibration
Do not calibrate the T6000 Series thermostat in the field.
Troubleshooting
After a power outage, the thermostat mode and all settings return as most recently used or
set.
Repair and Replacement
Do not attempt to repair the T6000 Series thermostat. In case of an improperly functioning
control, contact the nearest Johnson Controls
®
representative, and specify the desired product
code number. When contacting the supplier for a replacement please state the type/model
number of the control located on the data plate or cover label.
Specifications
Refer to Product Catalog for Details.
Function /
ࠀీ
Icon /
ႚ
Cool Mode / ⏣⍤㯎ゼ
Heat Mode / 䊚㯎ゼ
Fan only Mode / 橻㣧
Unoccupied / 㢶/㞍㯎ゼ
֖ຕఁ
Function
ఐ
嵑⇩
Factory
Setting
努
ࡤᅭ
Setting range
㗱㶼⓻㶼愙㔏 /
/ Changeover
A C F: 皓C:
嵫ⵇ㿖こᾷ柽⇩
Max.Temp setpoint
b 30 嵫ⵇ咰⢡
Setting Range 2盖49
嵫ⵇ㿖こᾸ柽⇩
Min.Temp setpoint
C 05 嵫ⵇ咰⢡
Setting Range 0盖47
⫞䛢捺◜
Restart when Power failure
d 0 0皒⌠枚 OFF皓
1皒キ◜ ON
ⷼ。㟫䫧
Screen Display
E 0 0皒 㟫䫧ⵑ⌲㿖こ Room Temp皓
1皒 㟫䫧嵫ⵇ㿖こ Setting Temp
㞍㯎ゼ〟宓䉦䑣ㆮ
Unoccupied Mode contact status
(Ὰ憯䛕※T6634-TA10-9JS0)
(Not available for T6634-TA10-9JS0)
F 1 0皒 〟宓䉦䦚㕒㞣ₐ娕㢶䑣ㆮ皓㝚キ㞣ₐ
娕㞍䑣ㆮ
Short connect contact for occupied
status, vice versa, unoccupied status
1皒 〟宓䉦㝚キ㞣ₐ娕㢶䑣ㆮ皓䦚㕒㞣ₐ
娕㞍䑣ㆮ
Short connect contact for unoccupied
status, vice versa occupied status
㞍㯎ゼ⏣⍤㿖こ
Unoccupied Temp Setpoint cooling
(Ὰ憯䛕※T6634-TA10-9JS0)
(Not available for T6634-TA10-9JS0)
g 28 23盖30҉
㞍㯎ゼ⏣䊚㿖こ
Unoccupied Temp Setpoint heating
(Ὰ憯䛕※T6634-TA10-9JS0)
(Not available for T6634-TA10-9JS0)
H 18 16盖23҉
厗㏃㏸㯎ゼ愙㔏
Auto/Manual changeover
(憯䛕※T6634-TF20-9JS0)
(Only for T6634-TF20-9JS0)
I 0 0皒㏸㯎ゼ愙㔏皓1皒厗㯎ゼ愙㔏
0: Manual changeover; 1: Auto changeover
To Next Page
Loading...
Need help?
General
