17
ENGLISH |
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
SUB.W
LEVEL
*
1
–08
—
+08
(
00
):Adjusts the subwoofer output level.
SUB.W
*
2
ON
/
OFF
: Turns on or off the subwoofer output.
SUB.W
LPF
*
1
THROUGH
:All signals are sent to the subwoofer. ;
LOW
55Hz
/
MID
85Hz
/
HIGH 120Hz
:Audio signals with frequencies lower than
55Hz/ 85Hz/ 120Hz are sent to the subwoofer.
FADER
*
3
*
4
R06
—
F06
(
00
):Adjusts the front and rear speaker output balance.
BALANCE
*
3
L06
—
R06
(
00
):Adjusts the left and right speaker output balance.
VOL
ADJUST –05
—
+05
(
00
):Presets the volume adjustment level of each source
(compared to the FM volume level). Before adjustment, select the source
you want to adjust. (“VOLADJFIX” appears if FM is selected.)
AMP
GAIN LOW
POWER
:Limits the maximum volume level to 30. (Select if the
maximum power of each speaker is less than 50W to prevent damaging
the speakers.);
HIGH POWER
:The maximum volume level is 50.
D.T.EXP
(Digital Track
Expander)
ON
:Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression.;
OFF
:Cancels.
TEL
MUTING
*
5
(For
KD-DB65
)
ON
:Mutes the sounds while using the cellular phone (not connected
through KS-BTA100).;
OFF
:Cancels.
L/O
MODE SUB.W
/
REAR
:Selects whether rear speakers or a subwoofer are
connected to the REAR/SW line out terminals on the rear panel (through
an external amplifier).
*
1
Displayed only when
[L/O
MODE]
is set to
[SUB.W]
and
[SUB.W]
is set to
[ON]
.
*
2
Displayed only when
[L/O
MODE]
is set to
[SUB.W]
.
*
3
This adjustment will not affect the subwoofer output.
*
4
If you are using a two-speaker system, set the fader level to
[00]
.
*
5
Does not work if
[BT
ADAPTER]
is selected for
[AUX]
in
[SRC
SELECT]
.
( 4)
DISPLAY SETTINGS
KD-DB65KD-DB95BT
1 Press and hold MENU.
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
Repeat step
2 until the desired item is selected.
3 Press MENU to exit.
To return to the previous setting item or hierarchy, press T/P.
Default:
XX
DISPLAY
DIMMER
Selects the display and button illumination adjusted in the
[BRIGHTNESS]
setting.
AUTO
:Changes between the day and night adjustments when you turn off
or on the car headlights. *
1
;
ON
:Selects the night adjustments.;
OFF
:Selects
the day adjustments.
BRIGHTNESS
Sets the button, display and USB input terminal brightness for day and night
separately.
1
DAY
/
NIGHT
:Select day or night.
2
Select a zone for setting.
( Illustration above)
3
Set the brightness level (
00
to
31
).
(Default:
BUTTON ZONE
:
DAY
:
25
;
NIGHT
:
09
DISP ZONE
:
DAY
:
31
;
NIGHT
:
12
)
SCROLL
*
2
ONCE
:Scrolls the display information once.;
AUTO
:Repeats scrolling at
5-second intervals.;
OFF
:Cancels.
*
1
The illumination control wire connection is required.
( 23)
*
2
Some characters or symbols will not be shown correctly (or will be blanked).
JS_JVC_KD-DB95BT_E_f_EN.indd 17JS_JVC_KD-DB95BT_E_f_EN.indd 17 11/22/2013 11:54:30 AM11/22/2013 11:54:30 AM
To Next Page
Loading...
Need help?
General
