JVC KD-DV7206 Installation & Connection Manual

3
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Removing the unit
Before removing the unit, release the rear section.
*
3
When you stand the unit, be careful not to damage the fuse on the rear.
*
3
઱቎৹ʹጅçʮ˻ʿ࠱๑ᖢנ௰ڄۘᎳീé
ϰ༬༬௏éׇ֤ϛᄮڸؼ˗
ʓࡒڄ࿌༱ڷΕʄյܓڄϯ༫ദҺéϨس઱Љᖅç׻ᄔ࠱Љᘕࢭ˔άڄཊçቁώJVC
ԆԾࡖᛏ˜ኀ׻ࢭ˔άաᏻ˙༿é
ëϨس઱ʿ঻ᇧ׆Ϩщ͸ᇧϙϯ༫ʹጅçᏻቁϐڄӑிʆ࢜գϯ༫é
Do the required electrical connections.
නм׿ᄔڄྐཔ௤૊é
Bend the appropriate tabs to hold the
sleeve firmly in place.
Ҿᛮጅೋڄߴдçӕࢭጅೋԕ֣Ϛᄭ
ڷػ˖é
When using the optional stay / ࠝ᎛Έᆊނ
Screw (option)
ᒘീ᎚·ڄ
Stay (option)
ᆉށ᎚·ڄ
Fire wall
Վػ
Dashboard
ᄭڷػ
Install the unit at an angle of less than 30˚.
અʹጅϯ༫Ϛ˲ؠ30˚ڄԴܾé
When installing the unit without using the sleeve / ࠝˀՠΈࢮጆೌϰ༬͵ጆ
In a Toyota car for example, first remove the car radio and install the unit in its place.
ᕙΉ೻(TOYOTA) ԆԾ޴բ ࡛ζ֊ԆԾЂࡖጅç೸݈અʹጅ༫ʈմڏڄт໯é
*
4
Not supplied for this unit.
*
4
ʿᎲʹጅಏաé
Flat type screws (M5 × 8 mm)
*
4
Ꮓᒘീ (M5 × 8 mm)*
4
Pocket
ڏೋ
Flat type screws (M5 × 8 mm)
*
4
Ꮓᒘീ (M5 × 8 mm)*
4
Bracket*
4
Ёࣙ*
4
Bracket*
4
Ёࣙ*
4
Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are
used, they could damage the unit.
ٍิ !ӕʹጅϯ༫ϚЁࣙʕç՟·8 mmۂڄᒘീéϨ՟·ཫۂڄᒘീç๡๑ᖢʹጅé
։͵ጆ
Ϛ؛ֈʹጅۮçᏻઅʹጅ݈௰ڄ֣׆֜௤૊௰˜ᖑළé
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
ݝ࿌׿Εçઅղػ଍ܓӕ˾಍ʈᆥç೸݈ძᗌ
ϙનղώ؁ղӕ˾çʹጅᎲ˃؁é
Instal1-3_DV7206_006A_pre.indd 3Instal1-3_DV7206_006A_pre.indd 3 1/18/06 9:04:23 AM1/18/06 9:04:23 AM

JVC KD-DV7206 Specifications

General

Brand	JVC
Model	KD-DV7206
Category	Car Receiver
Language	English