JVC KD-X172M User Manual

12
ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
[SUBWOOFER
SET]
[ON]: Turns on the subwoofer output. ; [OFF]: Cancels.
[SUBWOOFER
LPF]*1
[FRQ THROUGH]: All signals are sent to the subwoofer. ;
[FRQ55HZ]/[FRQ85HZ]/[FRQ120HZ]: Audio signals with frequencies lower
than 55 Hz/85 Hz/120 Hz are sent to the subwoofer.
[SUB.W
PHASE]*1*3
[REVERSE] (180°)/[NORMAL] (0°): Selects the phase of the subwoofer output
to be in line with the speaker output for optimum performance.
[FADER]
[POSITIONR06] to [POSITIONF06] ([POSITION00]): Adjusts the front and
rear speaker output balance.
[BALANCE]*4
[POSITIONL06] to [POSITIONR06] ([POSITION00]): Adjusts the left and
right speaker output balance.
[VOLUME
ADJUST]
[LEVEL–15] to [LEVEL+06] ([LEVEL 00]): Presets the initial volume level of
each source by comparing to the FM volume level. (Before adjustment, select
the source you want to adjust. “VOL ADJ FIX” appears if FM is selected.)
[AMPGAIN]
[LOWPOWER]: Limits the maximum volume level to 25. (Select if the
maximum power of each speaker is less than 50 W to prevent damaging the
speakers.) ; [HIGHPOWER]: The maximum volume level is 35.
[D.T.EXPANDER]
(Digital Track
Expander)
[ON]: Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in audio
data compression. ; [OFF]: Cancels.
[SPK/PREOUT] Depending on the speaker connection method, select the appropriate setting
for the desired output. (See the following “Speaker output settings”.)
*1 Displayed only when [SUBWOOFER SET] is set to [ON].
*2 Displayed only when [SPK/PREOUT] is set to [SUB.W/SUB.W].
*3 Selectable only if a setting other than [FRQTHROUGH] is selected for [SUBWOOFERLPF].
*4 This adjustment will not affect the subwoofer output.
Speaker output settings [SPK/PREOUT]
Select the output setting for the speakers [SPK/PRE OUT] , based on the speaker
connection method.
Connection via lineout terminals
For connections through an external amplifier. (Page 18)
Setting on
[SPK/PRE OUT]
Audio signal through lineout terminal
FRONT REAR SW
[REAR/REAR] (default) Front speakers
output
Rear speakers output Subwoofer output
[SUB.W/SUB.W] Front speakers
output
L (left): Subwoofer output
R (right): (Mute)
Subwoofer output
Connection via speaker leads
You can also connect the speakers without using an external amplifier
but still being able to enjoy the subwoofer output with these settings.
(Page 18)
Setting on
[SPK/PRE OUT]
Audio signal through rear speaker lead
L (left) R (right)
[REAR/REAR] Rear speakers output Rear speakers output
[SUB.W/SUB.W] Subwoofer output (Mute)
If [SUB.W/SUB.W] is selected:
– [FRQ120HZ] is selected in [SUBWOOFERLPF] and [FRQ THROUGH] is not available.
– [POSITION R01] is selected in [FADER] and selectable range is [POSITION R06] to
[POSITION 00].
Audio Settings
JS_JVC_KD_X172M_M2_EN_3.indd 12JS_JVC_KD_X172M_M2_EN_3.indd 12 6/12/2019 12:25:50 PM6/12/2019 12:25:50 PM

JVC KD-X172M Specifications

General

Brand	JVC
Model	KD-X172M
Category	Receiver
Language	English