JVC KD-X482DBT User Manual

2
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Basic procedure
1 Remove the key from the ignition switch, then disconnect the
terminal of the car battery.
2 Connect the wires properly. See “Wiring connection” on page 3.
3 Install the unit to your car. See the following “Installing the unit
(in-dash mounting)”.
4 Connect the terminal of the car battery.
5 Press B SRC to turn on the power.
6 Detach the faceplate and reset the unit within 5 seconds. See “How to
reset” on page 4.
Installing the unit (in-dash mounting)
Installation/Connection
This section is for the professional installer.
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
WARNING
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to
prevent a short circuit.
• To prevent short circuit:
– Insulate unconnected wires with vinyl tape.
– Be sure to ground this unit to the car’s chassis again after installation.
– Secure the wires with cable clamps and wrap vinyl tape around the wires that comes into contact with
metal parts to protect the wires.
CAUTION
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly
after use of the unit. Metal parts such as the heat sink and enclosure become hot.
• Do not connect the wires of speakers to the car chassis or Ground wire (black), or connect them in
parallel.
• Connect speakers with a maximum power of more than 50 W. If the maximum power of the speakers is
lower than 50 W, change the [AMPGAIN] setting to avoid damaging the speakers.
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the
terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on and off by the
ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working
properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse with
one that has the same rating.
Hook on the top side
Bend the appropriate tabs to hold the
sleeve firmly in place.
Dashboard of your car
KD-X482DBT_E_B5K-0883-00_EN_2nd Draft.indd 2KD-X482DBT_E_B5K-0883-00_EN_2nd Draft.indd 2 26/8/2021 12:09:14 PM26/8/2021 12:09:14 PM

JVC KD-X482DBT Specifications

General

DIN size	1 DIN
Clock mode	12h/24h
Output power	200 W
Product color	Black
Volume control	Rotary
Disc types supported	No
Audio output channels	7.1 channels
Maximum power per channel	50 W
Mobile operating systems supported	Yes
Audio formats supported	FLAC, MP3, WAV, WAVE, WMA
Display type	LCD
Illumination color	Blue, Red
USB version	2.0/3.2 Gen 1 (3.1 Gen 1)
Bluetooth version	4.2
USB port position	Front
Bluetooth profiles	AVRCP
USB connector type	USB Type-A
USB ports quantity	1
Bluetooth functions	Audiostreaming, Automatic pairing for Android, Automatic pairing for iPhone, Handsfree calling
FM band range	87.5 - 108 MHz
LW band range	153 - 279 kHz
FM usable sensitivity	6.2
Supported radio bands	DAB, FM, LW, MW
Preset stations quantity	42
Hands-free calling	Keep your hands on wheel with Bluetooth™ Hands-free calling. After pairing your compatible Bluetooth mobile phone to your TomTom GPS, you’ll be able to see incoming call information, make and answer calls, and talk hands-free through your device. You’ll e

Weight and Dimensions

Depth	100 mm
Width	182 mm
Height	53 mm
Weight	600 g