ENGLISH
11
Element
Size
Inner
Outer
Element
Size
Inner
Outer
Operating the DUAL Surface Element
The cooktops are equipped with a DUAL radiant surface
element located at the right front cooktop position (Figures 1
& 2). Indicator lights on the control panel at that position are
used to indicate what portions of the dual radiant element will
heat. The INNER light indicates that only the inner element
will heat. The OUTER light indicates that both inner and outer
elements will heat together. You may switch between these
different settings at any time during cooking.
Figure 1
Setting Surface Controls (cont’d)
Figure 2
Figure 3
Figure 4
Figure 5
once or twice (Figures 4 & 5 show indicator lights with OUTER and INNER elements selected). Note: If no element
size is chosen when the dual element is turned ON, the control will default to the inner coil only. If the pan sensing
feature is on, the element size key is disabled and the appropriate element size is automatically selected according to
the pan size.
5. Touch HI pad once to turn ON the power level to HI (See Figure 5). Touch Lo pad once for Lo.
6. Each touch of the HI or Lo pad will decrease or increase the power level from 9.5 through 3.0 by .5
increments. Simmer power levels between 3.0 and 1.2 will decrease or increase by .2 increments. Lo is the lowest
power level available.
Note: The power level may be adjusted at any time while the element is ON.
7. Start most cooking operations on a higher setting and then turn to a lower setting to finish cooking. Each surface
element provides a constant amount of heat at each setting. A glowing red surface heating area extending beyond the
bottom edge of the cookware indicates the cookware is too small for the surface heating area.
8. When cooking has been completed touch the
On/Off
pad once to turn the element OFF and if no other surface element
is used touch the
POWER
key pad to turn off the cooktop.
Note: The HE (hot element) message will remain ON if the cooktop is still hot and will remain ON until the heating
surface area has cooled sufficiently.
Radiant surface elements may appear to have cooled after they have been turned off. The glass surface
may still be hot and burns may occur if the glass surface is touched before it has cooled sufficiently.
Do not place aluminum foil or plastic items such as salt and pepper shakers, spoon holders or
plastic wrappings on top of the range when it is in use. These items could melt or ignite. Potholders, towels or wooden
spoons could catch fire if placed too close to the surface elements.
Hi
Lo
On/Off
Hi
Lo
On/Off
POWERON
Hi
Lo
On/Off
Element
Size
Front
+Bridge
All
Element
Size
Inner
Outer
Hi
Lo
On/Off
Warm
&Hold
Sensa
Cook
Timer
POWER
PanSensing
P
O
N
T
W
E
R
E
L
E
M
E
ge
P
O
N
T
W
E
R
E
L
E
M
E
Hi
Lo
On/Off
Hi
Lo
On/Off
POWERON
Element
Size
Front
+Brid
All
Element
Size
Inner
Outer
Hi
Lo
On/Off
Hi
Lo
On/Off
Hi
Lo
On/Off
Warm
&Hold
Sensa
Cook
Timer
POWER
PanSensing
Element
Size
Inner
Out er
Hi
Lo
On/ Off
To Operate the Dual Surface Element:
1. Place correctly sized cookware on the radiant
surface element.
2. Touch and hold the
POWER
key pad until a beep
sounds. The power indicator light will turn ON.
Note: If no key pad is touched within 20 seconds
the request to Power ON the cooktop will clear.
3. Touch and hold the
On/Off
pad for the dual
element position until a beep is heard. The
display will show " - - ".
Note: If no further pads are touched within 10
seconds the request to power the element ON will
clear.
4. If the pan sensing feature is off, select the
INNER (Figure 3) or OUTER (both elements)
(Figure 4) to heat by pressing the
Element
Size
pad
To Next Page
Loading...
Need help?
General