10
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
While listening to any source...
1 Press AUD to enter
[AUDIO CONTROL]
directly.
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press
.
Default:
XX
AUDIO CONTROL
SUB-W LEVEL
–15
to
+15
(
0
) Adjusts the subwoofer output level.
BASS LEVEL –8
to
+8
(
+2
)
Adjusts the level to memorize for each source. (Before
making an adjustment, select the source you want
to adjust.)
MID LEVEL –8
to
+8
(
+1
)
TRE LEVEL –8
to
+8
(
+1
)
EQ PRO
(This setting is stored to
[USER]
.)
BASS ADJUST BASS CTR FRQ 60
/
80
/
100
/
200
or
60HZ
/
80HZ
/
100HZ
/
200HZ
:
Selects the center frequency.
BASS LEVEL –8
to
+8
(
+2
):Adjusts the level.
BASS Q FACTOR 1.00
/
1.25
/
1.50
/
2.00
:Adjusts the quality factor.
BASS EXTEND ON
:Turns on the extended bass.;
OFF
:Cancels.
MID ADJUST MID CTR FRQ 0.5KHZ
/
1.0KHZ
/
1.5KHZ
/
2.5KHZ
:Selects the center
frequency.
MID LEVEL –8
to
+8
(
+1
):Adjusts the level.
MID Q FACTOR 0.75
/
1.00
/
1.25
:Adjusts the quality factor.
TRE ADJUST TRE CTR FRQ 10.0KHZ
/
12.5KHZ
/
15.0KHZ
/
17.5KHZ
:Selects the
center frequency.
TRE LEVEL –8
to
+8
(
+1
):Adjusts the level.
AUDIO SETTINGS
PRESET EQ DRIVE EQ
/
TOP40
/
POWERFUL
/
ROCK
/
POPS
/
EASY
/J
AZZ
/
NATURAL
/
USER
:Selects a preset equalizer suitable to the music genre. (Select
[USER]
to use the settings made in
[EQ PRO]
.)
[DRIVE EQ]
is a preset equalizer that reduces noise outside the car or
running noise of the tyres.
BASS BOOST LV1
/
LV2
/
LV3
or
LEVEL1
/
LEVEL2
/
LEVEL3
:Selects your preferred
bass boost level.;
OFF
:Cancels.
LOUDNESS LV1
/
LV2
or
LEVEL1
/
LEVEL2
:Selects your preferred low and high
frequencies boost to produce a well-balanced sound at a low volume
level.;
OFF
:Cancels.
SUBWOOFER SET ON
:Turns on the subwoofer output.;
OFF
:Cancels.
LPF SUBWOOFER THROUGH
:All signals are sent to the subwoofer.;
85HZ
/
120HZ
/
160HZ
:Audio signals with frequencies lower than
85Hz/120Hz/160Hz are sent to the subwoofer.
SUB-W PHASE REVERSE
(180°)/
NORMAL
(0°):Selects the phase of the subwoofer
output to be in line with the speaker output for optimum
performance. (Selectable only if a setting other than
[THROUGH]
is
selected for
[LPF SUBWOOFER]
.)
FADER R15
to
F15
(
0
):Adjusts the rear and front speaker output balance.
BALANCE L15
to
R15
(
0
):Adjusts the left and right speaker output balance.
VOLUME OFFSET
For AUX:
–8
to
+8
(
0
) ; For other sources:
–8
to
0
:Preset the initial
volume level of each source. (Before adjustment, select the source you
want to adjust.)
SOUND RECNSTR
(Sound reconstruction)
ON
:Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost
in audio data compression.;
OFF
:Cancels.
•
[SUB-W LEVEL]
/
[SUBWOOFER SET]
/
[LPF SUBWOOFER]
/
[SUB-W PHASE]
is
selectable only if
[SWITCH PREOUT]
is set to
[SUB-W]
or
[SUBWOOFER]
.
( 4)
•
[SUB-W LEVEL]
/
[LPF SUBWOOFER]
/
[SUB-W PHASE]
is selectable only if
[SUBWOOFER SET]
is set to
[ON]
.
ENGLISH
JS_KWD_KMM_203_ENE2N_EN_5.indd 10JS_KWD_KMM_203_ENE2N_EN_5.indd 10 26-Aug-16 3:50:08 PM26-Aug-16 3:50:08 PM
To Next Page
Loading...
Need help?
General
