KAP-1
PA/HA Switching Unit
KCT-18
Ignition Sense Cable
KCT-19
Accessories
Connection Cable
KCT-35
Extension Cable
for KGP-2A/2B
and KDS-100
KCT-36
Extension Cable
KDS-100
Mobile Data Terminal
KES-3
External Compact Speaker
(fits 3.5 mm ext. speaker jack)
KES-5
External Speaker
KGP-2A
GPS Receiver Modem
(requires KCT-35 option)
KGP-2B
GPS Controller Modem
(requires KCT-35 option)
KLF-2
Line Noise Filter
(in-line install with DC
power cable)
KMB-2B
Mounting Case
(for KPS-10A
power supply mounting)
KMB-10
Key Lock Adapter
(for mobile mounting
bracket)
KMB-20
Mounting Case for KPS-14
KMC-27A
Microphone
(MIL-SPEC, noise canceling)
KMC-27B
Microphone
(same as supplied)
KMC-28A
Keypad Microphone
(12 keys, MIL-SPEC,
noise canceling)
KMC-9C
Control Station
Desktop Microphone
KPS-15
DC Power Supply
ADS#111904(0) Printed in USA
Specifications
Applicable MIL-STD
Standard MIL 810C MIL 810D MIL 810E MIL 810F
Methods /Procedures Methods / Procedures Methods / Procedures Methods / Procedures
Low Pressure 500.1 /Procedure I 500.2 /Procedure I, II 500.3 /Procedure I, II 500.4 /Procedure I, II
High Temperature 501.1 /Procedure I, II 501.2 /Procedure I, II 501.3 /Procedure I, II 501.4 /Procedure I, II
Low Temperature 502.1 /Procedure I 502.2 /Procedure I, II 502.3 /Procedure I, II 502.4 /Procedure I, II
Temperature Shock 503.1 /Procedure I 503.2 /Procedure I 503.3 /Procedure I 503.4 /Procedure I, II
Solar Radiation (Sunshine) 505.1 /Procedure I 505.2 /Procedure I 505.3 /Procedure I 505.4 /Procedure I
Humidity 507.1 /Procedure I, II 507.2 /Procedure II, III 507.3 /Procedure II, III 507.4
Sand & Dust 510.1 /Procedure I 510.2 / Procedure I 510.3 / Procedure I 510.4 / Procedure I, III
Vibration 514.2 / Procedure VIII, X 514.3 / Procedure I Cat.8 514.4 / Procedure I Cat.8 514.5 / Procedure I Cat.20
Shock 516.2 / Procedure I,II,III,V 516.3 / Procedure I,IV,V 516.4 / Procedure I,IV,V 516.5 / Procedure I, IV, V
JQA-QMA1205
Kenwood follows a policy of continuous advancement in development.
For this reason specifications may be changed without notice.
TK-863G
GENERAL
Frequency range 450 ~ 490 MHz
Number of systems Max. 32
Number of groups Max. 250
Number of channels (Conventional mode) Max. 600
Channel spacing
Wide/Narrow 25kHz/12.5kHz
Channel step 5kHz, 6.25kHz
Channel spread 40 MHz
Current drain
Standby Less than 0.4A
Receive Less than 1.0A
Transmit Less than 8.0A
RF input impedance 50 Ω
Operating voltage 13.6 V DC±20%
Operating temperature range -22°F~ +140°F
(-30°C ~ +60°C)
Frequency stability ±2.5 ppm (-22°F ~ +140°F )
Dimensions (W x H x D) 5.51 x 1.57 x 5.70 in (140 x 40 x 145 mm)
Weight (net) 2.07 Ib (940 g)
FCC ID ALH29383110
FCC compliance FCC parts 22, 74, 90, 95
TK-863G
RECEIVER
(Measurements made per EIA/TIA-603)
Sensitivity (12 dB SINAD)
Wide/Narrow 0.28 µV/0.35 µV
Selectivity
Wide/Narrow 80 dB/65 dB
Intermodulation distortion
Wide/Narrow 75 dB/63 dB
Spurious response 85 dB
Audio output 4 W at less than 5% distortion
TRANSMITTER
(Measurements made per EIA/TIA-603)
RF power output 25 W
Spurious 65 dB
FM noise
Wide/Narrow 50 dB/45 dB
Modulation
Wide/Narrow 16K0F3E/11K0F3E
Audio distortion Less than 3%
Options
All accessories and options may not be available in all markets. Contact an authorized
Kenwood dealer for details and complete list of all accessories and options.
To Previous Page
Loading...
Need help?
Receiver Specifications
