说明书
Manual
产品基础
PRODUCT BASIC INFORMATION
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
WHEN USING A KEYBOARD:FCC WARNING:
1.Maintain proper posture and avoid excessive force on the keys.
2.Take regular breaks to prevent hand fatigue.
3.Clean the keyboard regularly to remove dust and dirt.
4.Avoid exposing the keyboard to liquids.
5.Keep the keyboard in a suitable environment, free from extreme temperatures or humidity.
This device complies with part 15 of the FCC Rules, Operation is subiect to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Any Changes or modifications not
expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
poursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications, However, there is no guarantee that interference wil not occur in
a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction.
Remember these tips for a comfortable and durable keyboard experience.
WIERD MODE
INDICATOR LIGHT
指示灯
有线模式
BT连接
BT CONNECTION
2.4G RECEIVER CONNECTION
BACKLIGHT CONTROL
背光控制
2.4G连接
尺寸/Size
329.4(L)×118.15(W)×37.9(H)±2
89.7(L)×132.5(W)×38.3(H)±2
背光/Backlit
RGB
有线/2.4G/BT
67 keys
19 keys
机械轴体
版本/Version 轴体/Key SwitchesLayout
USB-C wired/2.4G wireless/BT
Mechanical switches
拔轴拔键器
Switch and Keycaps Puller
键盘
Keyboard
Type-C 数据线
Type-C Cable
2.4G接收器
2.4G Receiver
USB Type-c
Setting the switch to the "B" position
Connect the USB cable to the device and set the switch to the middle position for wired mode.
连接USB至设备，旋钮拨到OFF为有线模式
Connect the USB to the device and turn the knob to "OFF" for wired mode.
(Note: Wired mode can only be used when the knob in the upper right corner is turned to "OFF".)
1. Switch to the "G" position.To pair the receiver,
2. long-press FN + 0. The 0 key will flash. Insert the receiver and wait for the flashing to stop,
indicating successful pairing.
拔动开关到BT1、BT2、BT3位置
Toggle switch to BT1、BT2、BT3 for BT Mode.
长按Fn+Q/W/E进入配对模式
长按Fn+1/2/3进入配对模式
Press and hold Fn+Q/W/E to pair with new BT devices
1. 旋钮开关拨到2.4G位置。
2. FN+P长按对码，P键闪烁插入接收器，P键停止闪烁即对码成功。
1.Switch to the 2.4G position,
2.Press and hold FN+P to pair,
As the P key flashing, plug the receiver into the device.
if the P key stops flashing, pairing is successful.
(温馨提示：出厂时已配对好接收器，无需自行再次配对2.4G；此方法只是2.4G无法连接的时候使用，首次设置即可，无需每次都设置)
(Tips: The receiver is set to be paired at the factory You just need to set it only once, when pairing not working properly.)
长按3秒，
恢复出厂设置
space
bar
支持多种背光效果切换
Multiple backlight effects switch
背光单色切换
Backlight monochrome switching
Switch between multiple dynamic backlight modes
Switch backlight colors
Backlight brightness +
Backlight brightness -
Long-press for three seconds
to restore factory settings
Long-press for three seconds
to restore factory settings
背光亮度+
Backlight brightness +
背光亮度-
Backlight brightness -
背光速度+
Backlight speed +
背光速度 -
Backlight speed -
Caps Lock
Num
Win Lock 充电指示:充电时呼吸状态、充满常亮、低电压闪烁
充电指示:充电时常亮、充满熄灭低电压时闪烁
Charging indicator: Solid light during charging, off when fully charged, and flashing when battery is low
(Recommended: Use a 5V 1A power supply for keyboard charging).
K68Pro
K20
K68PRO
K20
K68Pro K20
K68Pro K20
K68Pro K20
K68Pro K20
Charging indicator: Breath mode during charging, steady light when fully charged,
and low voltage blinking.
窗口锁定
Windows lock
BT1 BT2 BT3
BT1 BT2 BT3
1 2
3
有线模式：连接USB至设备，开关拨到中间为有线模式
开关拨到B状态
1. 开关拨到G状态。
2. FN+0长按对码，0键快闪烁插入接收器，0键停止闪烁即对码成功。
背光颜色切换
背光亮度增加
背光亮度减小
长按3秒，恢复出厂设置
多种动态背光模式切换
短按Fn+1/2/3至BT频道
Short press Fn+1/2/3 to BT channel
Long press Fn+1/2/3 to enter pairing mode
K68Pro
K20
KEYBOARD
MECHANICAL
To Next Page
Need help?
General
