Restoring the Factory Default EDID (Transmitter)
1. Power up the transmitter by
a. using one of the external power supply
b. connecting it to a DVI source.
2. Press and keep the LEARN button pressed. The EDID state LED goes dark for two
seconds, and then turns continuous orange to indicate that learn mode is activated.
(Do not connect the unit to a display device.)
3. Keep the button pressed until the LED starts to blink orange (after approximately
10 seconds). Five blinks indicate the EDID restore process.
4. After the restore process is nished, the LED blinks slowly green for 8 seconds. The
stored EDID is changed back to factory default (
1920x1200 @ 59.55Hz
).
5. The unit is ready to be used for DVI signal extension.
Troubleshooting
Some DVI sources may not supply enough power to the transmitter. Use one of the
external power supply methods in this case.
If the image is noisy make sure that the ber cable plugs are clean.
Typical Standalone Application
PC
Maximum Extension Distances
OM1
(62,5/125)
OM2
(50/125)
OM3
(50/125)
OM4
(50/125)
1080p@60Hz 24 bpp 250 m 600 m 1200 m 2500 m
Video Signal
Supported video signal ......................................................................................... DVI-D
Maximum resolution .................................................1920 x 1200 or 2048 x 1080 pixel
Data rate .............................................................................................. 1.65 Gbps/ color
Video delay .............................................................................................none (0 frame)
EDID emulation........................................................................Yes, with LEARN button
EDID memory ................................................................1 pc user programmable EDID
Factory EDID .............................................................................. 1920x1200 @ 59.55Hz
Optical
Optical cable .....................................................................................multimode, 50/125
Optical connector .......................................................................................................SC
Laser class specication.................................................................................. Class 3R
Laser wavelengths .................................................. 4 channel: 778; 800; 825; 850 nm
DVI-OPT-TX100 output OMA* ...........................................................-6.25 dBm (max.)
DVI-OPT-RX100 OMA* sensitivity ...................................................-14.25 dBm (max.)
Maximum transmission distance ...................... 2500m (using OM4 type optical cable)
*Optical Modulation Amplitude
Specication
General
Compliance ................................................................................................................CE
EMI / EMC ................................................................................. EN 55024 / EN 55032
Cooling. ...............................................................................................................passive
Weight (DVI-OPT-TX110 / DVI-OPT-RX110) ..............................................200g / 205g
Size. .............................................................................. 100.4 mm x 67.6 mm x 26 mm
Material ................................................................................................................... steel
Warranty ............................................................................................................. 3 years
Power
Power supply ........................................................................... external power adaptor
Power adaptor .............................................. (100 - 240 V AC, 50/60 Hz)(5V DC, 1 A)
Power connector ............................................................................ 1.35 / 3.5 mm barrel
Power consumption (DVI-OPT-TX110 / DVI-OPT-RX110) ..................... 1.4 W / 0.8 W
Connectors
DVI-OPT-TX110 input ................................................................................24-pole DVI-I
DVI-OPT-TX110 output................................................................................SC simplex
DVI-OPT-RX110 input .................................................................................SC simplex
DVI-OPT-RX110 output .............................................................................24-pole DVI-I
MX-DVI-OPT-IB-LC
8CH OPTICAL INPUT BOARD
LASER DETECT
RECEIVER ACTIVE
SIGNAL PRESENT
L. D.
R. A.
SIGNAL
IN1 IN2
IN7 IN8
IN5 IN6
IN3 IN4
SC 50/125 MULTIMODE
8CH OPTICAL INPUT BOARD
SC 50/125 MULTIMODE
8CH OPTICAL INPUT BOARD
IN1 IN2
IN7 IN8
IN5 IN6
IN3 IN4
LASER DETECT
RECEIVER ACTIVE
SIGNAL PRESENT
MX-DVI-OPT-IB-ST
4 CH DUAL LINK DVI INPUT BOARD
MX-DVIDL-IB
LC 50/125 MULTIMODE
LASER DETECT
RECEIVER ACTIVE
SIGNAL PRESENT
L. D.
R. A.
SIGNAL
IN1 IN2
IN7 IN8
IN5 IN6
IN3 IN4
LASER DETECT
RECEIVER ACTIVE
SIGNAL PRESENT
MX-DVI-OPT-IB-SC
OUT1 OUT2
OUT7 OUT8
OUT5 OUT6
OUT3 OUT4
8CH OPTICAL OUTPUT BOARD
8CH OPTICAL OUTPUT BOARD
SC 50/125 MULTIMODE
SC 50/125 MULTIMODE
MX-DVI-OPT-OB-ST
LASER DETECT
SIGNAL PRESENT
L. D.
SIGNAL
MX-DVI-TP-OB
8CH OPTICAL RECLOCKING
OUTPUT BOARD
MX-DVI-OPT-OB-NT
LASER DETECT
SIGNAL PRESENT
L. D.
SIGNAL
MX-DVI-OPT-OB-LC
8CH OPTICAL OUTPUT BOARD
LASER DETECT
L. D.
L. D.
OUT1 OUT2
OUT7 OUT8
OUT5 OUT6
OUT3 OUT4
LASER DETECT
MX-DVI-OPT-OB-SC
OUT1 OUT2
OUT7 OUT8
OUT5 OUT6
OUT3 OUT4
RS-232
LOCAL CONTROL
RoHS
Made in EU, HU
Service LAN
SC MM OUT DC 5V
Monitor
Monitor
Monitor
DVI-OPT-RX220-Pro
DVI-OPT-TX220-Pro
DVI
DVI
DVI
DVI
DVI
DVI
DVI-OPT-TX110
DVI-OPT-RX110
Projector
Projector
PC
Multimode
optical cable
up to 2500 m
MX-FR-80R
5V DC power
adaptor
5V DC
power
adaptor
Multimode Neutrik
optical cable
up to 2500 m
PC
Multimode Neutrik
optical cable
up to 2500 m
Multimode Neutrik
optical cable
5V DC Power
adaptor
Single fiber
multimode
optical cable
up to 2500 m
PC or Mac
DVI-OPT-TX110
DVI-OPT-RX110
Projector
Integrated System Application
To Previous Page
Loading...
Need help?
General
