Audio Cable Wiring Guide
HDMI-3D-OPT-RX150RA receiver is built with 5-pole Phoenix output connector. See below a
few examples of the most common assembling cases.
From balanced output to balanced input
Phoenix - 2 x 6.3 (1/4”) TRS
From balanced output to balanced input
Phoenix cable - 2 x XLR plugs
2
3
1
2
3
From balanced output to unbalanced input
Phoenix - 2 x RCA
From balanced output to unbalanced input
Phoenix - 3.5 (1/8”) TRS
For more information about audio cable wiring see the user’s manual of the device or the Audio
Cable Wiring Guide on our website www.lightware.eu.
Digital
audio/video
Digital
audio/video
HDMI
out
Fiber
optical
in
De-embedder
D/A converter
Analog
audio
Digital
audio
Digital
audio
S/PDIF
out
Analog
audio
out
USB 1
USB 2
RS-232
USB
(control
only)
Processor
USB KVM
USB KVM
RS-232
and
USB KVM
8CH OUTPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO
MX-HDMI-3D-OB-A
OUT 1
OUT 2
OUT 3
OUT 4
OUT 5
OUT 6
OUT 7
OUT 8
MX-HDMI-OPT-OB-SC
OUT 1
OUT 2
OUT 3
OUT 4
OUT 5
OUT 6
OUT 7
OUT 8
8CH OPTICAL OUTPUT BOARD
LASER ACTIVE
HDCP
HDMI
SINGLE FIBER
L.A
HDCP
HDMI
SINGLE
LASER ACTIVE
HDCP
HDMI
SINGLE PRESENT
LASER ACTIVE
HDCP
HDMI
SIGNAL PRESENT
LASER ACTIVE
HDCP
HDMI
SINGLE PRESENT
INPUT 1
INPUT 8
INPUT 7
INPUT 6
INPUT 5
INPUT 4
INPUT 3
INPUT 2
MX-HDMI-OPT-IB-SC
IN 1
IN 2
IN 3
IN 4
IN 5
IN 6
IN 5
IN 6
8CH OPTICAL INPUT BOARD
LASER ACTIVE
HDCP
HDMI
SINGLE FIBER
L.A
HDCP
HDMI
SINGLE
LASER ACTIVE
HDCP
HDMI
SINGLE PRESENT
LASER ACTIVE
HDCP
HDMI
SIGNAL PRESENT
LASER ACTIVE
HDCP
HDMI
SINGLE PRESENT
SW4-OPT-TX240RAK
MX-FR17
PC
PC
PIN: 2.1mm
RS-232
TX RX
LIVE
LASER ACTIVE
FIBER LINK
RS-232
12V 1A DC
HDMI OUT
SC MM
LASER APERTURE
OUTPUT
GPIO
1 2 3 4 5 6 7
6 AUDIO2 IN
5V DC
Power
adaptor
Monitor
Projector
HDMI-3D-OPT-RX150RA
5V DC
Power
adaptor
Laptop
Wireless
receiver
Tablet
Audio
amplifier
HDMI
HDMI
HDMI
HDMI
HDMI
DisplayPort
RS-232
Analog audio
Analog
audio
Single fiber multimode
optical cable up to 2500m
Single fiber multimode
optical cable up to 2500m
Single fiber multimode
optical cable up to 2500m
5V DC
Power
adaptor
PC
PIN: 2.1mm
RS-232
TX RX
LIVE
LASER ACTIVE
FIBER LINK
RS-232
12V 1A DC
HDMI OUT
SC MM
LASER APERTURE
OUTPUT
6 AUDIO2 IN
HHDDMMII--33DD--OOPPTT--TTXX221100RRAAKK
RS-232
A
A
A
A
HID
A
O
<=
mW
CLASSIFIED B
A
HDMI
USB
Monitor
Mouse
Keyboard
HDMI-3D-OPT-RX150RA
Audio amplifier
HDMI
RS-232
Analog audio
USB
USB
5V DC
Power
adaptor
Port Diagram
Factory Default Settings
Optical input port properties
HDCP Enabled
HDMI output port properties
Signal type Auto
HDCP mode Auto
Power 5V mode Always on
Test pattern mode Off
Test pattern clock source 480p
Test pattern Bar
Analog audio output port properties
Volume (%) 100
Volume (dB) 0.00
Balance 0 (center)
Bass (dB) 0
Treble (dB) 0
Phase invert Disabled
RS-232 settings
RS-232 mode Pass-through
Control protocol LW2
Port setting 57600 BAUD, 8, N, 1
Typical application
Standalone application
Typical application
Integrated system diagram
Maximum Fiber Cable Extension Distances
OM1 OM2 OM3 OM4
(62.5/125) (50/125) (50/125) (50/125)
1080p@60Hz 24 bpp 250 m 600 m 1200 m 2500 m
1080p@60Hz 36 bpp 150 m 400 m 800 m 1300 m
4096x2048@30Hz 24 bpp Not supported 350 m 700 m 1100 m
Audio Outputs
The table below shows the supported audio formats by output ports.
Audio formats
Audio outputs
Embedded
audio
S/PDIF output
Analog audio
output
Multichannel PCM
Max 8 channel,
up to 192 kHz
Stereo PCM
(up to 48 kHz)
Stereo PCM
(up to 48 kHz)
Dolby Digital 2.1
-
Dolby Digital 5.1
-
Dolby Digital 7.1
-
DTS 2.1
-
DTS 5.1
-
DTS 7.1
-
Dolby TrueHD (HBR)
- -
DTS-HD (HBR)
- -
DTS-HD Master Audio (HBR)
- -
All other HDMI specied
standards
- -
To restore factory default settings, do the following steps:
1. Keep the Function button pressed for 10 seconds.
2. After the front panel LEDS start to blink, release the button.
3. The device restarted and the factory default settings are restored.
To Previous Page
Loading...
Need help?
General
