Quick Start Guide
HDMI-TPS-RX110AY
Further Information
The document is valid with the following rmware version: 1.0.0
The product brief and further information are available on www.lightware.com.
See the Downloads section on the website of the product.
Contact Us
sales@lightware.com
+36 1 255 3800
support@lightware.com
+36 1 255 3810
Lightware Visual Engineering LLC.
Peterdy 15, Budapest H-1071, Hungary
Doc. ver.: 1.1
19200100
Important Safety Instructions
Please read and keep the information in the attached safety instructions supplied with the
product before you start using the device.
Introduction
Thank you for choosing Lightware HDMI-TPS-RX110AY receiver. The product has HDBaseT
TM
integration with additional Lightware developments. The device receives digital video at a
resolution up to 4K, audio, and control up to 170 m distance over a single CAT cable. The
receiver is compatible with Lightware TPS matrix and 25G boards as well as other TPS
products. The device can be remote powered over TPS link with PoE (IEEE 802.3af).
Box Contents
Receiver unit
12V DC adaptor with
interchangeable plugs
Phoenix Combicon 3-pole
connector
Phoenix Combicon 4-pole
connector
Infrared detector unit
Rear View
Front View
5
Ethernet connector RJ45 connector for remote controlling and rmware
upgrade via LAN.
6
Status LEDs LEDs give feedback about the current status of the unit
and connection signals.
7
Reset button Pushing the button reboots the unit.
8
Function button Special functions are available with this button (bootload
mode, DHCP settings, restore factory default settings,
condition launching in Event Manager).
1
Relay
connector
4-pole Phoenix connector for two relays controlling.
2
Infrared
connectors
2 TRS (3.5mm jack) connectors for Infrared units (IR IN for the
detector, IR OUT for the emitter)
3
USB
connector
USB interface for LDC connection to control and configure the
device.
4
RS-232
connector
3-pole Phoenix connector for serial communication.
1
12V DC input
connector
12V DC input for local powering.
2
TPS input port TPS input port for compatible transmitter device (extender /
matrix / board).
3
Signal LED for
HDMI output
LED gives feedback about current status output signal.
4
HDMI output
port
HDMI output port for DVI or HDMI signal. Connect an HDMI
cable between the receiver and the display device.
5
HDCP LED for
HDMI output
LED shows the current HDCP status of the video source.
6
Audio output
port
5-pole Phoenix connector for balanced analog audio output.
Status LEDs
LIVE
OFF: device is not powered.
BLINKING (slow; 1 sec): device is powered and operational.
BLINKING (fast; 0,5 sec): device is in bootload mode.
ON: device is powered but no operation.
RS-232
OFF: RS-232 ports (local and link) are in Pass-through mode.
BLINKING: Command Injection mode is active.
ON: RS-232 ports (local and link) are in Control mode.
AUDIO OUT
OFF: embedded audio is not present or muted.
BLINKING: embedded audio format is not supported for audio de-embedding.
ON: embedded audio is present and de-embedded.
TPS LINK
OFF: no TPS link.
BLINKING: Device is in low power or Ethernet fallback mode.
ON: TPS link is active.
Connecting Steps
Connect the receiver and the transmitter by a CATx cable via the TPS connectors.
Optionally connect the transmitter to a LAN network to control the device.
Optionally for relay extension: connect the controlled device(s) (e.g. projection
screen) to the relay port.
Optionally for Infrared extension:
Connect the IR emitter to the IR OUT port of the receiver, and/or
Connect the IR detector to the IR IN port of the receiver.
Optionally connect an audio device (e.g. audio amplier) to the audio output port.
Optionally for RS-232 extension: connect a controller/controlled device
(e.g. projector) to the RS-232 port.
Connect a sink to the HDMI output port.
Choose powering option:
A. Local powering: rstly connect the power adaptor to the DC input of the
receiver, then secondly to the AC power socket.
B. Powering by a power injector (PoE): connect the compatible transmitter
and a TPS-PI-1P1 power injector to the TPS input port of the receiver via a
CATx cable. The power injector needs to be powered by a local DC adaptor.
C. Powering by a matrix or output board (PoE): connect the compatible
matrix or output board to the TPS input port of the receiver via a CATx
cable. Output board needs to be powered by a local DC adaptor; please
check the user’s manual of the board.
Rear Panel LEDs
TPS Input LEDs
ON: remote power receiving (PoE) is active.
OFF: no TPS link between transmitter and receiver.
BLINKING: device is in low power mode or in Ethernet fallback mode.
ON: TPS link is active.
HDMI Output - SIGNAL LED
OFF: output signal is not present or muted.
ON: signal is present
HDMI Output - HDCP LED
OFF: output signal is not HDCP-encrypted.
BLINKING: non-HDCP capable device is connected, encrypted signal is replaced with red screen.
ON: output signal is HDCP-encrypted.
Compatible Devices
The receiver is compatible with other Lightware TPS devices, matrix TPS and TPS2 boards,
25G boards, as well as third-party HDBaseT-extenders, displays, but not compatible with the
phased out TPS-90 extenders.
The receiver is PoE-compatible (Power over Ethernet, can be powered remotely via
CATx cable) but the device can only receive power and cannot send power other PoE-
compatible devices.
Infrared emitter unit Safety and warranty info,
Quick Start Guide
The product is compatible with any third-
party HDBaseT
TM
devices.
HDBaseT
TM
and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
Mounting
To mount the receiver Lightware supplies optional accessories for different usage. There are
two kinds of mounting kits with similar xing method. The receiver has two mounting holes with
inner thread on the bottom side. Fasten the device by the screws enclosed with the accessory.
The Under-desk double mounting kit makes easy to mount a single device on any at surface,
e.g. furniture. 1U high rack shelf provides mounting holes for fastening two half-rack or four
quarter-rack sized units. Pocket-sized devices can also be fastened on the shelf. To order
mounting accessories please contact sales@lightware.com.
Using different (e.g. longer) screws may cause damage to the device.
The receiver is half-rack sized.
Under-desk double mounting kit 1U high rack shelf
Phoenix Combicon 5-pole
connector
Locking DC Plug
Twist 90° clockwise to lock.
HDMI
LAN
or output board
Powering Options
CATx
Projector
+48
+36
+24
+15
+10
+6
+48
+36
+24
+15
+10
+6
Power
Adaptor
A
B
CATx cable
C
TPS-PI-1P1
transmitter
Compatible
matrix or output board
Audio
IR
HDMI
Power
Safety and
Warranty
Info
Quick
Start
Guide
To Next Page
Need help?
General
