Makita DHP453T001 User Manual

2 ENGLISH
SPECIFICATIONS
Model: DHP343 DHP453
Drilling capacities Masonry 10 mm 13 mm
Steel 10 mm 13 mm
Wood 25 mm 36 mm
Fastening capacities Wood screw 5.1 mm x 63 mm 6 mm x 75 mm
Machine screw M6
No load speed High (2) 0 - 1,300 min
-1
Low (1) 0 - 400 min
-1
Blows per minute High (2) 0 - 19,500 min
-1
Low (1) 0 - 6,000 min
-1
Overall length 211 mm 232 mm
Rated voltage D.C. 14.4 V D.C. 18 V
Net weight 1.4 - 1.7 kg 1.7 - 2.0 kg
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydi󰀨erfromcountrytocountry.
• Theweightmaydi󰀨erdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge D.C.14.4 V Model BL1415N / BL1430B / BL1440 / BL1460B
D.C.18 V Model BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
DC18SH / DC18WC
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
andchargersmaycauseinjuryand/orre.
Symbols
The followings show the symbols which may be used
for the equipment. Be sure that you understand their
meaning before use.
Read instruction manual.
Ni-MH
Li-ion
Only for EU countries
Due to the presence of hazardous com-
ponents in the equipment, waste electrical
and electronic equipment, accumulators
and batteries may have a negative impact
on the environment and human health.
Do not dispose of electrical and electronic
appliances or batteries with household waste!
In accordance with the European Directive
on waste electrical and electronic equipment
and on accumulators and batteries and
waste accumulators and batteries, as well as
their adaptation to national law, waste elec-
trical equipment, batteries and accumulators
should be stored separately and delivered
to a separate collection point for municipal
waste, operating in accordance with the
regulations on environmental protection.
This is indicated by the symbol of the
crossed-out wheeled bin placed on the
equipment.
Intended use
The tool is intended for impact drilling in brick, brickwork
and masonry. It is also suitable for screw driving and drill-
ing without impact in wood, metal, ceramic and plastic.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-1:
Model DHP343
Sound pressure level (L
pA
) : 80 dB(A)
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Model DHP453
Sound pressure level (L
pA
) : 83 dB(A)
Sound power level (L
WA
) : 94 dB (A)
Uncertainty (K) : 3 dB(A)
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.

Makita DHP453T001 Specifications

General

Brand	Makita
Model	DHP453T001
Category	Drill
Language	English