Dear customer, thank you for purchasing a MASTER product. This guide contains information about the product use. Before the product installation and use, please read carefully this
guide and keep it for future reference. The device is designed for the control of tubular motors for moving awnings and the like. Any other use beyond the field defined by Master S.p.A.
is prohibited and involves, as well as the failure to comply with instructions provided in this guide, the cancellation of Master S.p.A. liability and warranty. The installer, after the
installation of the product, must teach the end user about the working way of the automation and provide him with the user manual.
This sensor does not protect awning in case of strong and sudden gusts of wind. In case of weather hazards of this type, make sure that the curtains remain closed! Master
S.p.A. declines all responsibility for damage incurred due to weather events not detected by the device.
MASTER uses packaging recyclable materials. Dispose materials on the proper containers, complying with the law in force in your locality.
This product may have substances that are polluting for the environment and dangerous for the health.
At the end of the product life cycle, carefully comply with the waste disposal rules. It is strictly forbidden to dispose the product on the domestic waste.
Disposal
It is advisable to avoid using radio systems in areas with strong interference (for example,
near police stations, airports, ports, hospital, etc). A technical inspection is in any case advisable
before installing any radio system in order to identify sources of interference.
Radio systems can be used where possible disturbances or malfunctioning of the transmitter or
the receiver do not cause a risk factor, or if the risk factor is cancelled by suitable safety systems.
The presence of radio device operating on the same transmission frequency (433,42 MHz) can
interfere with the radio receiver of the motor and so reduce the range of the system and limit the
functionality of the installation.
Notes on radio systems
01. MOUNTING
Incorrect installation can cause serious injuries ● Keep these instructions for future maintenance work and disposal of the product ● All the product installation, connection,
programming and maintenance operations must be carried out only by a qualified and skilled technician, who must comply with laws, provisions, local regulations and the instructions
given in this manual ● The wiring must comply with current IEC standards. The final electrical system must be created only by the electrician ● Some applications require hold-to-run
operation and can exclude the use of radio controls or require particular safety devices ● To prevent potentially dangerous situations, check the operating condition of the roller
shutter/awning regularly
01.1 Warning for safety
Read the technical specifications on the paragraph “Technical specifications” to evaluate the operating limits of the product ●
Before installing the product, check the compatibility with the associated devices and accessories ● Check that the package is
intact and has not been damaged in transit ● A heavy shock and the use of unsuitable tools can cause the damage of the
external or internal parts of the product ● Do not pierce or tamper with the product in any way. Do not modify or replace parts
without the manufacturer’s permission ● Check that the place chosen for the installation is made by solid material and can
ensure a stable fixation ● Check that the place chosen for the installation of the sensor is within the range of transmission-
reception generated by the sensor and by the receiver of the blind to be commanded ● Install the product with the cups pointing
downwards and with the body of the sensor horizontally (using a bubble level facilitates the operation, the attack on the wall with
tilting angle ± 90 ° allows you to mount the sensor on non-vertical structures) ● The product must be installed well exposed to
the sun-wind, away from heat sources (eg chimneys), away from obstacles that may interfere with the movement of the cups ● If
there are several radio appliances in the same system, they must not be less than 1,5m apart ● Do not install the product near
metal surfaces ● Do not use abrasive or solvent product for cleaning the device; do not clean using water or high-pressure
cleaners ● For your safety, do not work near the winding roller while the motor is powered
The product is not intended to be used by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they are supervised or given instructions about the product way of use by a person
responsible for their safety ● Check the automation during the movement and keep people at a safe distance, until the
movement ends ● Do not allow children to play with the appliance or with the fixed control devices ● Do not operate the blind
when maintanance operations are being carried out (e.g. window cleaning, etc.). If the control device is automatic, disconnect
the motor from the power line
01.2 Warning for installation
01.3 Warning for use
Power supply: 120 o 230 Vac, 50/60 Hz
Dimensions: 236 x 54 x 73 mm
Weight: 200 gr
Working temperature: –20°C / +55 °C
Wind threshold: 5 Km/h / 35 Km/h
Sun threshold (VEGA only): 1 Klux / 45 Klux
Frequency: 433.42 Mhz
Operating frequency band: 433,050 – 434,790 Mhz
- Max radiated power, e.r.p. : <10 mW
Range (estimated): 100m outdoor, 20m indoor
Technical specifications
X
Fix the wall support
using the supplied
plugs and screws
A
Close the two screws
that fix the wall support
and sensor
B
Insert the two screw
cover
C
Unscrew the screw and
open the closing cover
placed under the sensor
D
Plug up the provided
cable
E
Block the cable
through the provided
cable clamp
F
Close the cover
G
01.4 Mounting
Led WIND
Button P1
Led SUN
Button P2
Led MANOEUVRE
Button P3
Make connections with power supply disconnected ●Check that the power supply does
not depend from electrical circuits for lighting ●Always connect the motor to the grounding
system (yellow/green) ● The supply line must be equipped with a circuit breaker. The
supply line must be fitted with a device with a voltage category III, i.e. the distance between
the contacts must be of 3,5 mm at least ● The product doesn’t not provide any protection
against overloads or short circuits. Provide the supply line with an adequate protection to
the load, for example a fuse of maximum value 500 mA ● The section of the connecting
cables must be proportionate to their length and to the absorption of the load, and in any
case not less than 1,5 mm
02. ELECTRICAL CONNECTIONS
(1)
(1) this screws must never be completely unscrewedWARNING:
L (Phase)
N (Neutral)
MAIN
POWER
SUPPLY
connector
FUSE 500mA
brown
blue
BLAST
radio wind sensor
VEGA
radio sun/wind sensor
rev03.1 26.07.2017
R
433,42 MHz
To Next Page
Loading...
Need help?
General
