mod. SATURN
EYEBOLT
MOUNTING
X X
Dear Customer, thank you for purchasing a MASTER product. This manual describes the operations for a correct installation. The tubular
motors with mechanical limit switch series JUPITER, MERCURY and SATURN are suitable to command the main types of roller blinds.Any other use is improper and forbidden and it could
void manufacturer’s warranty. The technical characteristics are provided on the label stuck on the motor tube. These devices have not been studied to a continuous working. The installation
of the product must be done by a qualified technician.
Keep this document for future reference.
Disposal
01. WARNINGS
Incorrect installation can cause serious injuries Keep these instructions for future maintenance work and disposal of the product All the product installation, connection, programming
and maintenance operations must be carried out only by a qualified and skilled technician, who must comply with laws, provisions, local regulations and the instructions given on this
manual The electrical wiring must comply with current CEI standards Some applications require «hold-to-run» operations and can exclude the use of radio controls or require particular
safety devices To prevent potentially dangerous situations, check the operating condition of the roller shutter/awning regularly
01.1 WARNINGS FOR SAFETY
Check that the package is intact and has not suffered damages in transit Aheavy knock and the use of unsuitable tools can cause the damage of the external or internal parts of the motor
Do not pierce or tamper with the motor in any way. Do not modify or replace parts without the manufacturer’s permission Do not carry the motor by the power cable. The product may not be
used if the power cable is damaged. Do not try to replace the power cable Any screws needed to complete the installation must not come into contact with the motor The power of the
motor must be sufficient for the applied load (check the rated data shown on the motor) Some steps of programming and/or normal operations make use of the mechanical stops of the
roller shutter/awning. It is essential to choose a motor with the most suitable torque for the application, considering the actual traction of the roller shutter/awning, and to avoid motors that
are too powerfull Use winding rollers that are at lease 10/10 Leave 1-2 mm of right/left play on the winding roller Check that the shape and size of the drive pulley and adapter crown
correspond to the winding roller used. Adapters, support, and sundry accessoriesrelated to the motor must be chosen exclusively from the MASTER catalogue If the product is installed at
a height of less than 2.5 m from the floor or from another support surface, the mocving parts must be protected with a cover to prevent accidental access. In any case, ensure access for
maintanance work The power cable must be positioned in such a way that it does not come into contact with moving parts The power cable of the product is suitable for indoor
installation only. If installed outside, place the cable in a protective tube If there are several radio appliances in the same system, they must not be less than 1,5 m apart Do not install the
product near metal surfaces Position the buttons withing sight of the roller shutter/awning but a long way from its moving parts. Position the buttons more than 1.5 m from the floor The
motor are studied for residential use; the maximum continuous operating time is 4 minutes During operation the motor body becomes very hot, so be careful The motor contains a self-
resetting thermal cut-off, which stops the motor if it overheats. The motor returns to normal operation when its temperature drops below the safety limit (normally after 5 or 10 minutes) The
motor must be installed so that it cannot come into contact with liquids and in any case in a position protected from atmospheric agents The antenna cable carries line voltage. Do not cut
the antenna cable as this would be dangerous. If the antenna cable is damaged, replace the product For your safety, do not work near the winding roller while the motor is powered
01.2 WARNINGS FOR INSTALLATION
The product is not intended for use of persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are supervised or
given instructions on how to use the product by a person responsible for their safety Before operating on the roller shutter/awning, make sure there are no people or objects in the area
involved in its movement. Check the automation during the movement and keep people at a safe distance, until the movement ends Do not allow children to play with the appliance or with
the fixed control devices. Furthermore, keep the portable control devices (remote controls) out of reach of children Do not operate on the roller shutter/awning when maintenance
operations are being carried out (e.g. window cleaning). If the control device is automatic, disconnect the motor from the power line.
01.3 WARNING FOR USE
WE RECOMMEND, FOR A PROPER INSTALLATION, READ THIS MANUAL.
The manufacturer can not be held responsible for any damage caused by improper, incorrect or unreasonable use.
R
JUPITER MERCURY SATURN
tubular motor with mechanical limit switch
rev04 20.03.18
WIRED
02. ELECTRICAL CONNECTION
MAIN
POWER
SUPPLY
L
N
motor cable
brown
brown
blue
blue
yellow/green
yellow/green
black
black
7
Ground
Common
Manoeuvre 2
Cable lenght
Manoeuvre 1
To change the sense of rotation
simply reverse the wires
black and brown.
2500
dimensions in «mm»
Fuse 3,15A
ü The supply line must be equipped with a circuit breaker. The installer must fit an isolation device (with 3,5 mm minimum opening on the contacts) upstream of the system.
ü Make connections with power supply disconnected.
ü Check that the power supply does not depend from electrical circuits for lighting.
ü Command buttons are connected to the main voltage, so they must be properly insulated and protected.
ü The product doesn’t provide any protection against overloads or short circuits. You must provide, on the supply line, an adequate protection to the load, for example a fuse of maximum
value 3,15A.
02.1 WARNING FOR THE INSTALLER
Connect the motor as shown. You must connect the YELLOW-GREEN wire to ground system. The electrical specifications of the motor are given on the label applied to the motor
tube.
02.2 POWER SUPPLY
Use only button with momentary positions ( "hold-to-run" ) with mechanical interlock, do not use button with maintained position. It's absolutely forbidden to connect more control
buttons in parallel! The command button is subjected to the mains voltage and therefore must be adequately isolated and protected.
02.3 COMMAND BUTTONS
Environmental conservation is an everyone’s duty!! MASTER uses packaging recyclable materials. Dispose materials on the proper containers, complying with the law in force
in your locality. If you are an installer and you use many motors, please ask for cavities box packaging to your retailer or to the manufacturer, this is an environmental respectful
choice, that limits waste and considerably reduce the packiging materials. This product may have substances that are polluting for the environment and dangerous for the
health.At the end of the product life cycle, carefully comply with the waste disposal rules. It is strickly forbidden to dispose the product on the domestic waste.
To Next Page
Loading...
Need help?
General
