(10) Dry Scrub Floor Machine
Dry Scrub Floor Machine (7)
3.3 Transport:
Totransportthismachinefromthejanitor’sclosettothe
workarea:
• Lock the handle in the “up” position. Wind the cord
around the handles and the bottom cord hook.
• Tip the machine back onto the transport wheels. Push
or pull the machine by the handle, not by the cord or
any other part of the machine. Travel carefully.
4.0 Troubleshooting
Neveroperatethismachinewhentheequipmentisnotperformingasexpectedorwhen
anypartsarevisiblydamaged.Thecauseandsolutionforsomebasicproblemsare
describedbelow.Whenrepairisneeded,taketheequipmenttoanauthorizedrepair
servicecenter.
4.1 Machine will not Run:
• Circuit breakers are tripped in the building. Check and reset.
• Equipment is unplugged. Check plug at wall and at machine base. Plug in.
• Power cord failure. Test with a working power cord. Lock the handle up and tip the
motor back. Unplug the cord at the motor and plug the motor into your working
power cord.
IMPORTANT: this is just for testing! When you do this, you have removed the
safety handle controls from the circuit and you are sending power directly to the
motor. If the motor now spins, the problem is in the cord of the handle assembly. Seek
authorized repair service.
If the motor still does not work, the problem is either in the male connection at the
motor base or in the motor. Seek authorized repair service.
• Motor sparks or smokes. Seek authorized repair service.
4.2 Electrical Shock to Operator:
• Equipment wiring failure or electrical short in the machine. Seek authorized service.
• Poor grounding or no grounding. Test the outlet with a ground fault interrupter. Retain
certied electrician to inspect and repair grounding. NEVER clip off the ground plug
on your cord.
• Repeated circuit breaking. High amp draw and circuit breaking can be an electrical or
mechanical problem. Seek authorized repair service.
4.3 High Vibration:
• Pads are not centered on the pad driver. Tip machine back and re-center the pad.
• Uneven wear or warp to pad or brushes. Replace.
• Machine chassis is damaged by dropping. Replace.
7.0 Parts List
Item No. Description Part No. Qty.
1 Trigger Pins B-70 2
2 Switch Box Back Cover A-104-S 1
3 Cross Bar Screw B-22 2
4 Safety Interlock Assembly SIA-1 1
5 Handle Tube Screw B-23 2
6 Switch Box Closing Screws B-21 4
7 Strain Relief Clamp - Black M-213 1
8 Black Hand Grip - Red Band M-218-R 2
9 Ground Wire Screw B-68 2
10 Handle Tube Insert M-247 1
11 Handle Tube with Yoke Plated M-206 1
12 Cable Hook Screw B-2 2
13 Cable Hook A-164 1
14 Cam Assembly C-100 1
14a Complete Cam Assembly CCA 1
(Includes 1 each of Drawing Items
#13, 14, 15, 28, 29)
15 Rectangular Hole Cam Washer B-67 1
16 Straight Brace M-233 2
17 Flat Washer B-37 1
18 Split Washer B-39 1
19 Cam Lock Wing Nut B-25 1
20 Sliding Collar A-111 1
21 Cable Grommet B-63 1
22 Black Rubber Cable Connector M-249 1
23 Handle Tube Cable G-16 1
24 PVC Axel Sleeve 1” Diameter DS-PVC SLEEVE 1
25 Hub Caps V0038 2
26 Spring Washer B-51 2
27 9” Axel M-217 1
28 Yoke Bolt B-18A 2
29 Yoke Pin Screw B-14 1
30 Nylon Flat Washers DS-NFW 2
31 Yoke DS-Yoke 1
32 Yoke Nut B10 1
33 Yoke Nut B-19 2
34 50-Ft., 14/3-Gauge Power Cord - Red G-14-50/R 1
35 Switch Mounting Plate G-30-B 1
36 On-off Switch and Plate Assembly G-30-AB 1
37 Insulated Flag Wire Connector G-48 5
38 Switch Plate Wire Screw B-1 2
39 Int. Tooth Lock Washer B-35 1
40 Flat Hex Nut B-33 1
41 Trigger Return Hook Spring G-30-C-T057 1
42 Label - Switchbox 1
43 Switch Box Front A-103 1
44 Wire Nut G-47 1
45 Trigger A-105 2
46 16” Crossbar M-211-A 1
Complete Complete Handle Assy. w/ 50 Ft. Cord - Red M-100-50-R 1
To Next Page
Loading...
Need help?
General