23
Getting Started
☝ Attention When promped by the wizard, you have to re-set
the servo arms during model setup of VBar Control to get
them as close to the actual center postion as possible.
☝ Attention Disconnect and remove the receiver of your old
radio system from the helicopter.
☠ Danger Disconnect the ESC or move the motor away from
the main gear. This is to avoid the model accidentally
spooling up during the setup process.
☝ Attention On battery-powered helicopters, the ESC must
ALWAYS must be connected to ‘Colle/ESC’ on a fullsize
VBar with external sensor. In case it was connected to CH4
or Servo, please re-connect. On a Mini VBar, the ESC is
always connected to RX B.
☝ Attention On nitro-powered helicopters, the throttle servo
must ALWAYS be conntected to Servo (on fullsize VBars
with external sensor). In case it was connected to CH4 or
Colle/ESC, please re-connect.
☠ Danger Remove main rotor blades and tail rotor blades
during setup and initial tests of the power unit and gover-
nor.
☝ Attention After the update has been completed, the VBar
is no longer accessible and can no longer be set up using
the PC software. To perform an update to a newer 6.x rm-
ware, you must load the recovery rmware rst (see FAQ
on www.vstabi.info).
☝ Attention In case of an update gone wrong (interruption of
the process, e.g. due to battery failure, computer crash,
accidental disconnection of the USB lead or similar), please
see our FAQ on www.vstabi.info on how to recover your
VBar and start over.
☝ Attention To switch back to VBar rmware for use with ra-
dios other than VBar Control, see our FAQ on www.vstabi.
info on how to recover your VBar. After recovery, select an
appropriate rmware from the list in ‘File/Online Update’ of
the 5.x+ PC software. If necessary, get a license key from
www.vstabi.info.
☝ Attention You must create a new setup using the VBar
Control’s setup wizards for every VBar you convert to rm-
ware version 6.x. Parameters will not be transferred on an
already set-up 4.x or 5.x VBar. Setup les from older ver-
sions of the VBar software and rmware are not compatible
and can not be loaded into the VBar by copying on the
VBar Control’s internal memory.
☝ Attention VBar Control has only Apps for basic setup and
ight operations installed by default. Go to
Transmitter Set-
tings/Shop
to browse, install and en-/disable Apps.
ACE DS0606 333 Hz 1.500 µSec
ACE DS0606 n 333 Hz 760 µSec
Airtronics 94758 333 Hz 1.500 µSec
Airtronics 94761 333 Hz 1.500 µSec
Align DS 520 333 Hz 1.500 µSec
Align DS 525 M 333 Hz 1.500 µSec
Align DS 620/650 333 Hz 1.500 µSec
Align DS 651 333 Hz 1.500 µSec
Futaba S 9253 333 Hz 1.500 µSec
Futaba S 9254/9257 333 Hz 1.500 µSec
Futaba S 9451 333 Hz 1.500 µSec
Futaba S 9650 333 Hz 1.500 µSec
Futaba S 3153 333 Hz 1.500 µSec
Futaba S 3154 333 Hz 1.500 µSec
Futaba BLS 451 333 Hz 1.500 µSec
Futaba S 9251/9256 333 Hz 760 µSec
Futaba BLS 251 333 Hz 760 µSec
Futaba BLS 256 HV 333 Hz 760 µSec
Futaba BLS 257 333 Hz 1.500 µSec
Graupner HBS 770 333 Hz 1.500 µSec
Hitec 5925 MG 333 Hz 1.500 µSec
Hitec 6965 HB 333 Hz 1.500 µSec
Hitec HSG-5083MG 333 Hz 1.000 µSec
JR 8900 G 333 Hz 1.500 µSec
JR 3400G 333 Hz 1.500 µSec
JR 2700 G 200 Hz 1.500 µSec
JR 8700 G 200 Hz 1.500 µSec
JR 810 G 200 Hz 1.500 µSec
JR MP 80 G 333 Hz 1.500 µSec
JR SPG 01 333 Hz 1.500 µSec
JR MP 83 GWV 333 Hz 1.500 µSec
Logictech 2100 G 333 Hz 1.500 µSec
Logictech 6100 G 333 Hz 1.000 µSec
MKS HBL 950 HV 333 Hz 1.500 µSec
MKS HBL 980 HV 333 Hz 760 µSec
MKS HBL 669 333 Hz 760 µSec
MKS BLS 980/990 333 Hz 760 µSec
MKS DS 95 i 333 Hz 760 µSec
MKS DS 760 333 Hz 760 µSec
MKS 8910A 333 Hz 760 µSec
Robbe FS 61 BB 333 Hz 1.500 µSec
Savox SB-2272/2 MG 333 Hz 1.500 µSec
Savox SC-1257 TG 333 Hz 1.500 µSec
Savox SH-1290 MG 333 Hz 1.500 µSec
Sky HDS-577 200 Hz 1.500 µSec
Sky HDS-877 200 Hz 1.500 µSec
Torq BL 9188 HV 333 Hz 760 µSec
Torq BL 9088 333 Hz 760 µSec
☝ Note: if your type of servo is not in this list, please look up
the parameters in the manual of the servo or on the inter-
net.
To Previous Page
Loading...
Need help?
General
