What to do if tapping icons doesn't work on Motorola Handhelds MC67?
M
Mark TranSep 4, 2025
If tapping icons or window buttons doesn't activate features on your Motorola MC67, the screen may not be calibrated correctly. Re-calibrate the screen by pressing the Blue key - Backspace key. If that doesn't work, the device may not be responding, try resetting it.
V
Valerie RhodesSep 18, 2025
How to enable sound on Motorola MC67?
W
warrenmooreSep 18, 2025
If there is no sound on your Motorola Handhelds, the volume setting may be low or turned off. Adjust the volume.
J
Joseph GuzmanSep 16, 2025
Why Motorola Handhelds MC67 does not turn on but two LEDs blink?
I
Isaac JonesSep 16, 2025
If your Motorola Handhelds MC67 doesn't turn on, but two LEDs are blinking, the battery charge is at a level where data is maintained, but the battery should be recharged. Charge or replace the battery in the MC67.
A
Alison JohnsonSep 14, 2025
Why is data not transmitting correctly on my Motorola Handhelds MC67?
M
Michael VasquezSep 14, 2025
If data isn't transmitting correctly on your Motorola Handhelds MC67, it could be because the device was removed from the cradle or disconnected from the host computer during communication. Replace the MC67 in the cradle, or reattach the communication cable and re-transmit. Another potential cause is incorrect cable configuration.
L
lovecameronSep 12, 2025
How to fix 'MC67 memory is full' message on Motorola Handhelds?
H
Harry CastroSep 13, 2025
If you're seeing an 'MC67 memory is full' message on your Motorola Handhelds, it's likely because too many files are stored on the device. Try deleting unused memos and records. If the issue persists, it could be due to too many applications installed. Remove user-installed applications to free up memory by tapping > Settings > System tab, then tap the Remove Programs icon, select the unused program, and tap Remove.
J
johnharrisSep 12, 2025
What to do if Motorola MC67 battery did not charge?
R
Rachel FrankSep 12, 2025
If the Motorola Handhelds battery isn't charging, the battery may have failed, so replace it. Also, make sure that the ambient temperature is not below 0°C (32°F) or above 40°C (104°F), as this can prevent charging. Ensure the MC67 remains in the cradle until charging is complete; a 3600 mAh battery fully charges in less than six hours.
I
iphillipsSep 9, 2025
Why is the battery LED flashing and Motorola Handhelds MC67 won't turn on?
K
Kyle HarmonSep 9, 2025
If the Charging/Battery Status LED flashes and your Motorola MC67 won't turn on, the battery is likely low. Recharge the battery.
C
Christina BakerSep 7, 2025
How to restore sound on Motorola Handhelds MC67?
A
amathisSep 7, 2025
If there is no sound on your Motorola MC67, the volume setting might be low or turned off. Adjust the volume.
R
Ryan FryeSep 5, 2025
Why Motorola Handhelds MC67 cannot find Bluetooth devices?
S
Sean GardnerSep 6, 2025
If your Motorola MC67 can't find Bluetooth devices, you might be too far from the other Bluetooth devices; move closer, within 10 meters (32.8 feet). Also, ensure the other Bluetooth devices are turned on and set to discoverable mode.
A
Andres MorganAug 20, 2025
Why won't my Motorola Handhelds MC67 turn on?
N
nicholsonjenniferAug 20, 2025
Your Motorola MC67 may not be turning on because the battery is not charged, so charge or replace it. Another reason could be that the battery is not installed properly, make sure it's correctly installed. Finally, the system may have crashed, in that case, perform a reset.