English-12
Specifications
Monitor Specifications MultiSync E221W Notes
LCD Module Diagonal: 55.9 cm/22.0 inches Active matrix; thin film transistor (TFT) liquid
Viewable Image Size: 55.9 cm/22.0 inches crystal display (LCD); 0.282 mm dot pitch;
Native Resolution (Pixel Count): 1680 x 1050 250 cd/m
2
white luminance; 1000:1 contrast ratio,
typical.
Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Digital Input: DVI-D with HDCP
Sync: Separate sync.TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. Positive/Negative
Sync on Green (Video 0.7 Vp-p and Sync Negative 0.3 Vp-p)
Display Colours 16,777,216 Depends on display card used.
Synchronization Range Horizontal: 31.5 kHz to 81.1 kHz (Analog) Automatically
31.5 kHz to 81.1 kHz (Digital) Automatically
Vertical: 56.0 Hz to 75.0 Hz Automatically
Viewing Angle Left/Right: ±88° (CR > 5)
Up/Down: ±85° (CR > 5)
Image Formation Time 5 ms (Typ.)
Resolutions Supported 720 x 400*
1
: VGA text Some systems may not support all modes listed.
640 x 480*
1
@ 60 Hz to 75 Hz
800 x 600*
1
@ 56 Hz to 75 Hz
832 x 624*
1
@ 75 Hz
1024 x 768*
1
@ 60 Hz to 75 Hz
1152 x 864*
1
@ 75 Hz
1152 x 870*
1
@ 75 Hz
1280 x 960*
1
@ 60 Hz to 75 Hz
1280 x 1024*
1
@ 60 Hz to 75 Hz
1440 x 900*
1
@ 60 Hz to 75 Hz
1400 x 1050*
1
@ 60 Hz to 75 Hz NEC DISPLAY SOLUTIONS cites recommended
1680 x 1050 @ 60 Hz..........................resolution for optimal display performance.
Active Display Area Horiz.: 473.8 mm/18.7 inches
Vert.: 296.1 mm/11.7 inches
Power Supply AC 100-240 V ~ 50/60 Hz
Current Rating 0.75 - 0.4 A
Dimensions 507.8 mm (W) x 374.0 - 424.0 mm (H) x 240.0 mm (D)
20.0 inches (W) x 14.7 - 16.7 inches (H) x 9.4 inches (D)
Height Adjustment: 50 mm/2 inches
Weight 6.3 kg (13.9 lbs)
Environmental Considerations
Operating Temperature: 5°C to 35°C / 41°F to 95°F
Humidity: 20% to 80%
Altitude: 0 to 6,562 Feet / 0 to 2,000 m
Storage Temperature: -10°C to 60°C / 14°F to 140°F
Humidity: 10% to 85%
Altitude: 0 to 40,000 Feet / 0 to 12,192 m
*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is
normal and necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on
the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.
NOTE: Technical specifications are subject to change without notice.
To Next Page
Loading...
Need help?
General