10
TOLL FREE: 1-800 -798 -7398
www.ninjakitchen.com
11
IMPORTANT: Never run the appliance
empty.
CAUTION: Use extreme caution when
processing hot foods or liquids to avoid
accidental scalding or burns. Do not
process food or liquid that is hotter than
180°F/82°C. Allow very hot ingredients
to cool before processing.
When processing hot foods or liquids,
always open the pouring spout cap to
vent the steam. Keep hands and other
exposed skin away from the opening to
prevent possible burns or scalding.
WARNING: Secure the blender while
in use by pressing down on the lid with
one hand.
WARNING: Never leave the blender
unattended while in use.
6 When you have reached your desired
consistency, stop the appliance by
turning the knob to the “OFF” position
and wait for the blades to stop turning.
Depending on the consistency of the
contents, remove the pitcher (Fig. 6)
and then open the pouring spout cap to
empty the liquid contents.
For thicker consistencies, remove the lid
by pressing the release button, lifting
the handle up and pulling the lid straight
up. (Fig. 7) Remove the blade assembly
carefully (by its shaft) and then empty
the contents of the pitcher.
CAUTION: Always use a spatula to
dislodge food that has stuck to the sides
of the pitcher. Never insert your hands in
the pitcher as the blades are sharp.
CAUTION: Never remove the pitcher
while the blender is still running.
7 Unplug the appliance after use.
Using the Ninja
®
Professional Blender - cont’d
Fig. 6
Fig. 7
HOW TO CLEAN
CAUTION: Make sure that the motor
base is unplugged from the power
source before inserting or removing any
attachment and before cleaning.
CAUTION: DO NOT immerse the motor
base into water or any other liquid. Clean
with a damp sponge or cloth and wipe
dry.
1 The pitcher, lid and blade assembly are
all dishwasher safe. It is recommended
that the lid and blade assembly be placed
on the top rack.
2 You may also wash the blender by filling
¾ of the pitcher with warm water and a
drop of dish washing detergent, placing
the lid on the pitcher and pressing the
pulse button a few times. Once clean,
Care & Maintenance
To order additional parts and accessories, please visit our website:
www.ninjakitchen.com or feel free to contact customer service: 1-800-798-7398.
Replacement Parts
remove the pitcher from the motor base.
Rinse the pitcher, blade assembly and lid
under running water. Allow all the parts
to dry before storing.
Use extreme caution when handling
the blade assembly as blades are very
sharp.
Please call customer service if any
servicing needs to be performed on the
appliance at 1-800-798-7398.
HOW TO STORE
1 Store the Ninja
®
Professional Blender
upright with the pitcher, blade assembly
and cover on the motor base. Do not
place anything on top.
2 Tuck power cord in cord storage
compartment in the back of the unit.
Troubleshooting Guide
PROBLEMS POSSIBLE REASONS & SOLUTIONS
Motor Doesn’t Start
or Blades Don’t
Rotate.
Make sure the pitcher is securely placed on motor base.
Make sure the lid is securely on pitcher in the correct position (align
arrows).
The blender is turned Off. Turn the knob to "PULSE" or "ON".
Check that the plug is securely inserted into the electrical outlet.
Check the fuse or circuit breaker.
The unit has overheated. Unplug and wait approximately 15 minutes
before using again.
Make sure that the ready light is a solid green and that the
appliance is assembled correctly.
You Cannot Achieve
Snow From Solid Ice.
Do not use ice that has been sitting out or has started to melt. Use
ice straight from the freezer.
OFF
PULSE
ON
BL500_30_IB_ENG_110223_2.indd 10-11 11-02-23 3:18 PM
To Next Page
Loading...
Need help?
General
