NuTone Heat-A-Ventlite 9965-R02 - User Manual

1
INSTALLATION INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS!
Heat-A-Ventlite
®
(with Night Light)
MODEL: 9965-R02
FOR BEST RESULTS
In a new construction site, install the housing (complete
with heater and ventilator) during rough-in construction of the
building. The light assembly and the grille should be installed
when the finished ceiling is in place.
Installation in an existing, finished building requires an
accessible area (attic or crawl space) above the planned
location. See “INSTALLATION IN EXISTING
CONSTRUCTION.”
Do not install closer than 12 inches to a vertical surface.
Do not install over tub or shower enclosure.
• For installation in sloped ceilings up to 12/12 pitch.
• Ductwork must point up.
UNIT DIMENSIONS
Refer to Figure 1 for housing's dimensions.
NOTE: If there will be a finished second floor above,
the Model 9965 housing requires a minimum of 2" x 8"
joist construction for mounting.
WIRING AND DUCTWORK
1. Run the required wiring during rough-in stage of
construction.
2. Total connected load: 1730 watts.
3. Plan to run 120vAC, 60 Hz wiring (with ground) on a
separate 20 Amp circuit from a power source, through
the provided wall switch, to the housing's junction box.
See wiring diagram.
4. Use 4" round duct.
FIGURE 1
7
3
⁄ 4 "
14"
9
3
⁄ 4 "
IMPORTANT INSTRUCTIONS
READ ALL INSTR UCTIONS BEFORE INSTALLING OR USING THIS
HEATER.
To reduce the risk of fire, electric shock, or injury to persons, observe the
following:
1. Use this unit only in the manner intended by the manufacturer. If you
have questions, contact the manufacturer at the address or
telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel
and lock the service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
4. When cutting or drilling into wall or ceiling, do not damage electrical
wiring and other hidden utilities.
5. This heater is hot when in use. To avoid burns, do not let bare skin
touch hot surfaces. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, etc. and curtains at least 3 feet
(0.9 m) from the front of the heater.
6. Extreme caution is necessary when any heater is used by or near
children or invalids and whenever the heater is left operating and
unattended.
7. Do not operate any heater after it malfunctions. Disconnect power at
service panel and have heater inspected by a reputable electrician
before reusing.
8. Do not use outdoors.
9. To disconnect heater, turn controls to off, and turn off power to heater
circuit at main disconnect panel (or operate internal disconnect
switch, if provided).
10. Do not insert or allow foreign objects to enter any ventilation or
exhaust opening, as this may cause an electric shock or fire, or
damage the heater.
11. To prevent a possible fire, do not block air intakes or exhaust in any
manner.
12. A heater has hot and arcing or sparking parts inside. Do not use it in
areas where gasoline, paint, or flammable vapors or liquids are used
or stored.
13. Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or
injury to persons.
14. Install heater at least 12 inches from floor or any adjacent wall.
15. To avoid electrical shock: Do not install unit in a tub or shower
enclosure or any location where it may come in contact with water.
Never place a switch where it can be reached from a tub or shower.
16. This product is designed for installation in ceilings up to a 12/12 pitch.
Duct connector must point up. DO NOT MOUNT THIS PRODUCT IN
A WALL.
17. Do not connect heater to dimmer switch or speed control.
18. Ducted fans must always be vented to the outdoors.
19. Provide a separate 20 AMP circuit. Use 12 GA. power cable of type
which meets code.
20. This product must be grounded.
SAVE THESE INSTRUCTIONS
30042496C

Summary

IMPORTANT INSTRUCTIONS

General Safety Precautions

Essential safety warnings for operation, handling, and installation to prevent fire, shock, or injury.

INSTALLATION IN NEW CONSTRUCTION

Preparation

Steps for preparing the housing, including hanger bar brackets and wiring knockouts.

Mounting the Housing

Securing the main housing unit between ceiling joists using hanger bars.

Installing the Ductwork

Connecting the duct collar and duct to the housing unit.

INSTALLING THE SWITCH

Switch Box and Wiring

Installing the double-gang switch box and running wiring.

INSTALLING AND CONNECTING THE WIRING

Wiring Connections and Grounding

Making electrical connections as per the diagram, ensuring proper grounding.

MOUNTING THE GRILLE ASSEMBLY

Grille, Reflector, and Lens Installation

Attaching the reflector, securing the grille, and installing light bulbs and lens.

INSTALLATION IN EXISTING CONSTRUCTION

Planning and Preparation

Reviewing new construction steps and checking overhead space for existing installations.

Installation Steps

Detailed steps for fitting housing, ductwork, and wiring in existing structures.

OPERATION

Pre-Use Check

Verifying proper installation before operating the heater.

MAINTENANCE

Bulb Replacement

Information on replacing incandescent and night light bulbs.

Cleaning Procedure

Monthly cleaning steps involving power disconnection and grille cleaning.

SERVICE PARTS

Parts Identification Diagram

Visual diagram identifying numbered service parts for the unit.

Parts List and Numbers

A detailed list of part numbers, descriptions, and cross-references.

WARRANTY INFORMATION

One Year Limited Warranty

Details the warranty coverage, limitations, and claim procedures.

NuTone Heat-A-Ventlite 9965-R02 Specifications

General

Voltage	120 V
Bulb Type	Incandescent
Fan CFM	70 CFM
Color	White
Material	Steel
Type	Heater with Light and Fan
Housing Material	Steel