To Next PageTo Next Page
Need help?Do you have a question about the OEM 8.6CAH12A and is the answer not in the manual?
Always wear safety glasses or goggles and appropriate clothing when operating.
Pump is designed for non-flammable fluids and not for explosive environments.
Do not allow children to operate; never point discharge at people or animals.
Product and exhaust contain chemicals known to cause cancer or birth defects.
Ensure guards cover moving parts and perform routine maintenance.
Use only components rated for the pump's flow and pressure.
Do not run the unit for more than two minutes without the trigger pulled.
Details on the standard garden hose inlet and M22 discharge connections.
Valve opens to release water when internal pump temperature rises too high.
System for mixing cleaners or solvents with water for improved cleaning.
Protect against backflow when connected to a potable water system.
Install shaft key and apply anti-seize on the engine shaft.
Align key ways and push pump onto engine, then install and torque bolts.
Use low pressure and specific solutions. Rinse system after use.
Be aware of hot surfaces, pressure, or moving parts during maintenance.
Periodically check and clean the filter by flushing it with water.
Use Pump Guard for storage over 30 days or in freezing temperatures.
Manufacturer agrees to repair/replace defective parts; excludes normal wear.
Excludes rental use, shipping damage, abuse, misuse, neglect, and non-factory repairs.
Warranty does not apply to failures due to freight damage, chemical deterioration, or freeze damage.
Addresses oil leaks between crankcase and pumping section, often due to worn rod oil seals.
Troubleshooting premature packing failure caused by plungers or overpressure.
Diagnosing pump running without flow, possibly due to fluid material or pressure.
Resolving issues where the pump fails to prime, often due to air or dry running.
Addressing prime loss, chattering noise, and pressure fluctuations from air leaks.
Troubleshooting low pressure at the nozzle due to clogged strainers or unloader valve issues.
Identifying causes for pressure gauge fluctuations, such as worn valves or packing.
Resolving low pressure by checking engine RPM, inlet plumbing, or nozzle size.
Always wear safety glasses or goggles and appropriate clothing when operating.
Pump is designed for non-flammable fluids and not for explosive environments.
Do not allow children to operate; never point discharge at people or animals.
Product and exhaust contain chemicals known to cause cancer or birth defects.
Ensure guards cover moving parts and perform routine maintenance.
Use only components rated for the pump's flow and pressure.
Do not run the unit for more than two minutes without the trigger pulled.
Details on the standard garden hose inlet and M22 discharge connections.
Valve opens to release water when internal pump temperature rises too high.
System for mixing cleaners or solvents with water for improved cleaning.
Protect against backflow when connected to a potable water system.
Install shaft key and apply anti-seize on the engine shaft.
Align key ways and push pump onto engine, then install and torque bolts.
Use low pressure and specific solutions. Rinse system after use.
Be aware of hot surfaces, pressure, or moving parts during maintenance.
Periodically check and clean the filter by flushing it with water.
Use Pump Guard for storage over 30 days or in freezing temperatures.
Manufacturer agrees to repair/replace defective parts; excludes normal wear.
Excludes rental use, shipping damage, abuse, misuse, neglect, and non-factory repairs.
Warranty does not apply to failures due to freight damage, chemical deterioration, or freeze damage.
Addresses oil leaks between crankcase and pumping section, often due to worn rod oil seals.
Troubleshooting premature packing failure caused by plungers or overpressure.
Diagnosing pump running without flow, possibly due to fluid material or pressure.
Resolving issues where the pump fails to prime, often due to air or dry running.
Addressing prime loss, chattering noise, and pressure fluctuations from air leaks.
Troubleshooting low pressure at the nozzle due to clogged strainers or unloader valve issues.
Identifying causes for pressure gauge fluctuations, such as worn valves or packing.
Resolving low pressure by checking engine RPM, inlet plumbing, or nozzle size.
General| Brand | OEM |
|---|---|
| Model | 8.6CAH12A |
| Category | Water Pump |
| Language | English |
