Onkyo A-RV401 User Manual

System connections
a
General
Switch the main power switch off before performing connections.
Aliso be sure to perform left and right channel connections properly.
COMPACT DISC
PLAYER
TURNTABLE
TAPE DECK-2
or GRAPHIC
EQUALIZER
RECORDER
OUTPUT
GND OUTPUT
REC PLAY REC REC
Lirm LIRR CIR LIAR VV
L
Ss rn ee ee eee
HoH” | o
P|
OO
VOLTAGE SELECTOR
Worldwide models only
REC PLAY
OUT PUT
TAPE DECK-1
or DAT
AC Outlets
@ SWITCHED:
These outlets are switched on and off by the system power switch
on the front panel and remote control transmitter. The total
capacity is 100 watts.
Turntable Connections (PHONO)
Connect the output leads of the turntable to the PHONO jacks.
Be sure to connect the ground (earth) lead wire from the turntable
to the ground terminal (GND). Lack of proper ground connection
will cause hum. Turntables not provided with GND wires do not
need to be connected.
1. Place the turntable on a firm shelf or deck free from vibrations
(especially those generated by the speaker system). !f the
turntable ts permitted to pick up such unwanted vibrations, not
only with the performance of the unit drop, but distortion in the
bass frequencies and howling in the speakers may also occur.
2. Check the turntable instruction manual for any other precautions.
3. The loud noises that occur when connecting and disconnecting
the turntable leads, replacing the cartridge or lowering the
tonearm could damage the speakers. Always turn the power
switch off before making connections.
4. lf an ONKYO turntable with remote control jack is used with
this unit, the remote control transmitter can also be used to start
and stop turntable operation. In this case, the turntable and
A-RV401 must be connected with a remote control cable. Insert
the plug into the PHONO jack of the REMOTE CONTROL on
the rear panel of this unit. (Please refer to “Connections for
Remote Control.)
Tuner Connections
Connect an FM/AM tuner to the tuner input jacks. Be sure the left
and right channels are connected properly.
Compact Disc Player Connections
Connect a compact disc player to the CD input jacks. Be sure the
left and right channels are connected properly.
VIDEO CASSETTE
PLAY PLAY
SPEAKER
IMPEDANCE
Aor B: 8 ohms MIN./SPEAKER RIGHT
A+ B:16 ohms MIN./SPEAKER
Note to CATV system installer:
This reminder is provided to call the CATV system instalier’s at-
tention to Aricle 820-22 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close
to the point of cable entry as practical.
MONITOR TV
SPEAKER (A} SPEAKER(A)
Vv
AC POWER
SUPPLY CORD
SPEAKER(B) SPEAKER(B)
VIDEO DISC PLAYER
or VIDEO CASSETTE
PLAYER (VCR-1}
fOUTPUT)
VIDEO AUDIO
Tape Deck (DAT} and Graphic Equalizer Connections
(FTAPE-1/DAT, TAPE-2)
1. This unit has facilities for two tape decks. If you are using only
one tape deck, connect it to the TAPE-1 jacks. If you have two
tape decks, connect one to the TAPE-1 jacks and the other to
the TAPE-2 jacks.
2. Connect the output leads of the tape decks to the TAPE-1 and
TAPE-2 “PLAY” jacks. Connect the input leads of the tape decks
to the TAPE-1 and TAPE-2 “REC” jacks of the unit. For more
details, refer to your tape deck instruction manual.
3. To connect 4 graphic equalizer, too, use the TAPE-2 jacks and
connect the second tape deck to the tape jacks of the equalizer.
To connect a graphic equalizer and second tape deck
to the TAPE-2 jacks.
To TAPE-2 “REC” jacks of A-RV401
To TAPE-2 “PLAY” jacks of A-RV401
EQUALIZER
Graphic equalizer
Second tape deck

Onkyo A-RV401 Specifications

General

Brand	Onkyo
Model	A-RV401
Category	Amplifier
Language	English