Onkyo A-RV401 User Manual

Operations
eee eee eee as
NOTE:
Before turning Power on, confirm that all connections have
been made properly.
@ For remote contro! operation refer to the Remote Control
Transmitter Controls section.
Standby Mode
The standby position of controls and switches serves as the starting
point for all modes of operation. When the system power button
is then turned on (while the main power switch is also on), all
controls except the speaker selector, bass/selective tone, treble,
volume,
balance
controls,
simulated
stereo
are
in
the
same
setting
as when the system power button was last switched off.
Speaker Selector Selected in accordance with connections 3.
16] Bass/Selective Tone Switch as desired
Bass Contral/Selective Tone Control Knob DEFEAT 4.
Simulated Stereo Switch as desired 5.
[9] Treble Control Knob DEFEAT
Balance Control Knob DEFEAT
Volume
Control
Knobs
minimum
(all
the
way
to
the
left)
6.
Main Power Switch ON
Radio Reception
1.
2
TAPE-2 button [15h is off.
. Follow the operating instructions of the Tuner.
Phonograph Records
1.
2
TAPE-2 button is off.
_ Follow turntable operating instructions.
Compact Disc Player
1.
2
Press the CD Input Selector button [14], and confirm that
TAPE-2 button is off.
. Follow the operating instructions of the CD player.
Tape Playback
1.
2.
Press the TAPE-1/DAT Input Selector button or TAPE-2
button depending on which pair of TAPE PLAY jacks the
deck is connected to. (Be sure to connect tape deck with the
FRE mark to the TAPE-1/DAT jacks.)
Follow tape deck operating instructions for playback.
NOTE:
The direct function feature
When a tuner, compact disc player, and tape deck with
the
fQE
mark
are
connected
together,
the
direct
function
feature
can
be
used.
Just by directly operating the desired component (tuner, com-
pact disc player, or tape deck), the A-RV401's input selector
automatically switches to that component. The component that
was being used stops, and the desired component starts oper-
ation. Therefore, it is not necessary to switch the A-RV401's
input selector when changing listening sources.
Example
When the compact disc player's play button is pressed, the
A-RV401's input selector will switch automatically to “CD.” If
the current listening source was a tape deck, tape playback will
stop and the compact disc player will start playing.
Note:
| The direct function feature does not apply to turntable. |
Press the TUNER Input Selector button [14], and confirm that
Press the PHONO Input Selector button [14], and confirm that
Tape Recording
1.
>
Radio: Press the TUNER input Selector button.
Records: Press the PHONO Input Selector button.
CD: Press the CD Input Selector button.
VCR-1/VDP: Press VCR-1/VDP Input Selector button.
VCR-2: Press the VCR-2 Input Selector button.
Put the tape deck connected to the TAPE-1/DAT jacks or
TAPE-2 jacks in the recording mode.
Set the proper recording level using the controls on the tape
deck used for recording. During recording and dubbing oper-
ations,
never
change
the
positions
of
any
controls
(bass,
treble,
etc.) on this unit.
Tape-to-Tape Duplicating
1.
Connect two tape decks to the A-RV401 as shown in the System
Connections diagram.
Load the original tape in the tape deck connected to the
TAPE-1/DAT jacks.
Load the blank tape in the tape deck connected to the TAPE-2
jacks.
Press the TAPE-1/DAT and TAPE-2 buttons [15].
Put the tape deck connected to the TAPE-1/DAT jacks in the
playback
mode
and
the
other
deck
in
the
recording
mode.
Follow
tape deck operating instructions.
The signal returned from the tape deck connected to the TAPE-2
jacks to the A-RV4017 can be monitored via speaker or head-
phones only if the tape deck is 3-head model.
Graphic Equalizer
1.
2.
Connect the graphic equalizer to the TAPE-2 jacks.
If a second tape deck is used, connect it to the tape jacks on
the graphic equalizer.
Press the TAPE-2 button [15].
Follow the graphic equalizer operating instructions.
To record an equalized signal, use tape deck 2 (connected to
the equalizer) for recording.
Video Disc Player Playback
1.
Connect
the
video
disc
player
to
the
A-RV401
as
shown
in
the
System
Connections
diagram.
Then
connect
a
monitor
or
TV
having
a
video
input
jack
to
the
A-RV401
VIDEO
“MONITOR
OUT"
jack.
Press the VCR-1/VDP Input Selector button [14].
Switch on the monitor TV. and start playback of the video disc
player. The picture will be sent to the monitor TV and sound
to the speakers.
Refer to the video disc player instruction manual for additional
information.
Video Cassette Recorder (or Player) Playback
1.
This
unit
has
facilities
for
two
video
cassette
recorders.
Connect
the
VCR
to
the
A-RV401
as
shawn
in
the
System
Connections
diagram.
Note
that
a
playback-only
video
unit
has
no
video
or
audio
input
jacks.
Remember
to
switch
the
corresponding
VCR-2
MODE
switch
to
MONO
when
using
a
monaural
VCR-2.
(See
page.4.)
If
this
is
not
done,
sound
will
be
heard
from
only
one
speaker.
If
the
MONO
setting
is
used
with
a
hi-fi
(stereo)
VCR,
even
stereo
sound
wili
be
heard
in
the
monaural
mode.
Then
connect
a
monitor
TV
or
TV
having
a
video
input
jack
to
the
A-RV401
VIDEO
“MONITOR
OUT"
jack.
Press the VCR-2 Input Selector button [14].
Switch on the monitor TV, and start playback of the VCR. The
picture will be sent to the monitor TV and sound to the speakers.
Refer to the video cassette recorder instruction manuat for ad-
ditional information.

Onkyo A-RV401 Specifications

General

Brand	Onkyo
Model	A-RV401
Category	Amplifier
Language	English