QUICK START GUIDE
B-HYVE XD BLUETOOTH®
HOSE FAUCET TIMER
FAUCET
CONNECTION
ZONE ZONE
RAINDELAYICON
FILTER
DIAL
ZONE
BUTTON
LOW
BATTERY
INDICATOR
BLUETOOTH®
ICON
Write down the MAC address: 12 digit alphanumeric
code located on the bottom of the timer.
Timer MAC Address: __ __ :__ __ :__ __ :__ __ :__ __ :__ __
Installing the Batteries
Insert two AA (1.5V) alkaline batteries (not included) and
replace the tray.
Replace batteries when low battery icon appears
on display.
Used up or dead batteries must be removed
from the timer and disposed of properly. Do not
dispose of batteries in fire. Batteries may explode
or leak. Remove batteries when storing timer.
Note: Firmly replace the battery tray to ensure water
resistance and increase battery life. You will know the
battery tray is fully inserted if it does not pull out easily.
Open the B-hyve® App
Log into your B-hyve account and tap “My B-hyve”. Go to
“devices” then “add device”. Select the B-hyve XD timer.
The app will walk you through the rest of the process.
For new users, search apps for “B-hyve” and
download the free Android or iOS app. Create an
account to begin setup.
The Bluetooth® icon on the display should be
flashing indicating the timer is in pairing mode.
If at any time you need to re-pair or do a factory
reset, turn the dial so the arrow is pointing to
OFF, press and hold the dial for 5 seconds.
Note: Your display will show lock icon to indicate that
the timer is using the B-hyve app to program your timer.
Note: When the display shows a full screen of symbols
release the dial. The display will show 12:00 pm in the
AUTO/MANUAL mode verifying the reset has been
completed. Resetting the timer will erase all programs
and it will need to reprogrammed to your desired
watering schedule.
PROGRAMMING THE TIMER
AT THE FAUCET
PROGRAMMING THE TIMER
WITH BLUETOOTH®
Set Clock
1. Turn the dial so the arrow is pointing to SET CLOCK.
2. Press the dial to confirm the selection, the hour will
begin to flash.
3. Turn the dial until the current hour is displayed
including the correct AM or PM, then press the dial to
confirm the selection. The minutes will begin to flash
indicating the next step in the process.
4. Turn the dial until the current minutes are displayed,
then press the dial to confirm the selection.
Programming Zone 2
1. Turn the dial so the arrow is pointing to Start Time.
2. Press the Zone Button to select zone 2.
3. With zone 2 now selected, repeat the steps for
Start Time, How Long, and How Often.
AUTO MODE
1. Turn the dial so the arrow is pointing to
AUTO/MANUAL.
2. Press the dial to confirm the selection, the arrow will
stop flashing and you are now in AUTO mode.
Start Time
1. Turn the dial so the arrow is pointing to START TIME.
2. Verify zone 1 is selected, noted by the zone number on
the display. To switch zones, press the zone button.
3. Press the dial to confirm the selection, the time slot
will begin to flash.
4. Turn the dial until the desired start time hour is
displayed including the correct AM or PM, then press the
dial to confirm the selection. The minutes will begin to
flash, indicating the next step in the process.
How Often
1. Turn the dial so the arrow is pointing to HOW OFTEN.
2. Press the dial to confirm the selection, the number slot
will begin to flash.
3. Turn the dial until the desired interval is displayed,
then press the dial to confirm the selection.
Note: 1 day is every day, 2 days is every other day, etc.
How Long
1. Turn the dial so the arrow is pointing to HOW LONG.
2. Press the dial to confirm the selection, the time slot
will begin to flash.
3. Turn the dial until the desired number of minutes are
displayed. Press the dial to confirm the selection.
Zone 1 is now programmed! You can now follow the
steps to program Zone 2, or you can skip to the Auto
Mode Section.
Congratulations!
Your timer is now programmed. The display will flash
between the current time and how long until the next
start time.
more information on back
Printers are responsible
for meeting print
production requirements.
Any changes must be
approved by Orbit
®
.
Printed piece must meet
designated specifications
on this form.
© 2020 Orbit Inc.
This work is the property
of Orbit
®
, and cannot
be used, reproduced or
distributed in any way
without their express
permission.
Dieline
PMS
0000
Fold
PMS
0000
Product
Coverage
PMS
0000
Dims./
Callout
PMS
0000
∙
∙
∙
∙
Orbit
®
1.801.299.5555
orbitonline.com
K
Glue
Folded Flat Additional Information
PRIN TERS ARE
REQUIRED TO MATCH
ALL SP ECIFIED
PMS COLORS.
DATE: 05/04/2021
DESIGNER: NK MARKETING: CD
SOFTWARE: Adobe Indesign CC
ARTWORK №: 24632-24 rB
L:
W:
H:
_._" W:
H:_._"
_._"
22.5"
5.5"
5. Turn the dial until the desired minutes are displayed,
then press the dial to confirm the selection.
While watering is in process, the dial at the
timer will deactivate and will not scroll until the
current watering cycle is finished. To stop activate
watering press the dial.
To Next Page
Need help?
General
