■
Press the – button to reverse clock time
(hold button for quick reverse).
START TIME
■
Press the + button to advance start time
(hold button for quick advance).
■
Press the – button to reverse start time
(hold button for quick reverse).
HOW LONG
Set watering duration from 1 to 240 minutes using
the + and – buttons.
HOW OFTEN
Set watering frequency as every 6 hrs, 12 hrs, or
from 1 to 7 days using the + and – buttons. 1 is
every day, 2 is every other day etc. up to 7 days.
AUTO
Timer waters according to programmed time,
duration, and frequency.
RAIN DELAY
■
When in AUTO, press + button for 24 hrs,
48 hrs, or 72 hrs.
■
Screen will flash between clock and hours
remaining before programmed cycle resumes.
■
To remove rain delay, turn dial to OFF and then
back to AUTO.
MANUAL/HAND WATERING
To water without interrupting the set cycle, press
INSTALLING THE BATTERIES
■
Remove the tray on the back of the timer by
sliding it out.
■
Insert two AA (1.5V) alkaline batteries
(not included) and replace the tray.
■
Replace batteries when low battery icon appears.
INSTALLATION
■
Attach timer to an outdoor hose faucet and turn
on after programming.
PROGRAMMING THE TIMER
■
Rotate the dial to positions indicated for setup.
SET CLOCK
■
Press the + button to advance clock time
(hold button for quick advance).
PN 62062-24 rE
dual outlet dIGItal tImer
■
PROGRAMMING FOR THE DIGITAL
PORT OF THE TIMER
■
THE MANUAL PORT CANNOT BE
PROGRAMMED DIGITALLY
[MANUAL] button and then use + and – buttons to
set from 1 to 240 minutes.
■
To remove manual watering (turn off),
turn dial to OFF.
■
To resume programmed cycle turn the
dial back to AUTO.
MANUAL PORT
The manual port of the timer gives access to the
hose faucet without interrupting the programmed
cycle of the digital port.
■
Open the valve in the port by turning the lever
counterclockwise to the open position.
■
Close the valve by turning the lever to the
closed position.
TROUBLESHOOTING
Water does not come on at desired time.
Check if:
■
Clock is set to correct time including AM and PM
■
Start time is set to desired time including
AM and PM
■
Rain Delay is on
Timer does not water.
Check if:
■
Faucet is on
■
Timer is set to AUTO
■
Hose faucet is on
■
Batteries are low
■
Clock is set to correct time including AM and PM
■
Rain Delay is on
Water won’t turn off.
Check if:
■
Watering duration is set to desired time
■
Start times begin after previous watering cycle
has run through all stations and set durations
■
For bypass/manual port: close valve
Working Water Pressure
Minimum: 25 psi Maximum: 100 psi
Working Temperature
Maximum: Do not exceed 120 degrees F
Minimum: Keep from freezing
Warnings
For outdoor use with cold water only.
WHEN EXPECTING FREEZING TEMPERATURES,
TIMERS SHOULD BE REMOVED FROM THE HOSE
BIB TO AVOID POTENTIAL FREEZE DAMAGE.
p 801 295 9820
f 801 951 5815
www.fluid-studio.net
1065 South 500 West
Bountiful, Utah 84010
proof no: 1
date: 5.23.11
des: SH spck: SH
job no:
client:
ORB
sku: 62062
upc: NA
file name: 62062-24 rE.indd
software: InDesign CS5
colors
additional instructions:
· Font sizes cannot be smaller than 7 pt.
· Proofing Code: LB412365
·
color non
printing
Die
PMS
???
color non
printing
Glue Area
color non
printing
Product Position
PMS
???
Registration
Black
Printers are responsible for
meeting print production
requirements. Any changes
must be approved by the
client and Fluid Studio.
printed piece must meet
designated specifications
on this form.
dimensions:
flat: w: 12.0" h : 6.0"
finished: w 3.0" d: 0 h 3.0"
© 2011 Fluid Studio. This
work is the property of Fluid
Studio, and cannot be used,
reproduced or distributed
in any way without their
express permission.
© 2011 Orbit Irrigation Products, Inc.
All rights reserved. All trade names are
registered trademarks of respective
manufacturers listed.
Orbit
®
Irrigation Products, Inc.
North Salt Lake, UT 84054
1-800-488-6156
www.orbitonline.com
To Next Page
Need help?
General
