SET CLOCK
■
Press the + button to advance clock time
(hold button for quick advance).
■
Press the – button to reverse clock time
(hold button for quick reverse).
START TIME
■
Press the + button to advance start time
(hold button for quick advance).
■
Press the – button to reverse start time
(hold button for quick reverse).
HOW LONG
Set watering duration from 1 to 240 minutes
using the + and – buttons.
HOW OFTEN
Set watering frequency as every 6 hrs, 12 hrs,
or from 1 to 7 days using the + and – buttons.
1 is every day, 2 is every other day etc.
up to 7 days.
AUTO
Timer waters according to programmed time,
station, duration, and frequency.
RAIN DELAY
■
When in AUTO, press + button for 24 hrs,
48 hrs, or 72 hrs.
■
Screen will flash between clock and hours
remaining before programmed cycle
resumes.
■
To remove rain delay, turn dial to OFF
and then back to AUTO.
INSTALLING THE BATTERIES
■
Remove the tray on the back of the timer
by sliding it out.
■
Insert two AA (1.5V) alkaline batteries
(not included) and replace the tray.
■
Replace batteries when low battery
icon appears.
INSTALLATION
■
Attach timer to an outdoor hose faucet
and turn on after programming.
PROGRAMMING THE TIMER
■
Rotate the dial to positions indicated
or setup.
■
Press station button to switch between
station 1 and 2 for all programming.
PN 27133-24 rC
dual-Outlet dIGItal tImer
■
PROGRAMMING FOR THE
DIGITAL OUTLET OF THE TIMER
MANUAL/HAND WATERING
To water without interrupting the set cycle,
press [MANUAL] button and then use + and –
buttons to set from 1 to 240 minutes.
■
To remove manual watering (turn off),
turn dial to OFF.
■
To resume programmed cycle turn the
dial back to AUTO.
TROUBLESHOOTING
Water does not come on at desired time.
Check if:
■
Clock is set to correct time including
AM and PM.
■
Start time is set to desired time including
AM and PM.
■
Rain Delay is on.
Timer does not water.
Check if:
■
Timer is set to AUTO.
■
Hose faucet is on.
■
Batteries are low.
■
Clock is set to correct time including
AM and PM.
■
Rain Delay is on.
Water won’t turn off.
Check if:
■
Watering duration is set to desired time.
■
Start times begin after previous
watering cycle has run through all
stations and set durations.
WHEN EXPECTING FREEZING TEMPERATURES, TIMERS
SHOULD BE REMOVED FROM THE HOSE BIB TO AVOID
POTENTIAL FREEZE DAMAGE.
p 801 295 9820
f 801 951 5815
www.fluid-studio.net
1065 South 500 West
Bountiful, Utah 84010
proof no: 2
date: 08.29.11
des: SH spck: SH
job no: N/A
client:
ORBIT
sku: 27133
upc: N/A
file name: 27133-24 rC.indd
software: InDesign CS5
colors
additional instructions:
· Font sizes cannot be smaller than 7 pt.
·
· Proofing Code: LB486038
color non
printing
Die
PMS
???
color non
printing
Glue Area
color non
printing
Product Position
PMS
???
Registration
Black
Printers are responsible for
meeting print production
requirements. Any changes
must be approved by the
client and Fluid Studio.
printed piece must meet
designated specifications
on this form.
dimensions:
flat: w: 12.0" h: 6.0"
finished: w 3.0" d: 0 h 3.0"
© 2011 Fluid Studio. This
work is the property of Fluid
Studio, and cannot be used,
reproduced or distributed
in any way without their
express permission.
© 2011 Orbit Irrigation Products, Inc.
All rights reserved. All trade names are
registered trademarks of respective
manufacturers listed.
Orbit
®
Irrigation Products, Inc.
North Salt Lake, UT 84054
To Next Page
Need help?
General
