EasyManuals Logo
Home>Peavey>Amplifier>PV 1

Peavey PV 1 User Manual

Peavey PV 1
10 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #7 background imageLoading...
Page #7 background image
12
Specifications PV
®
1 PV
®
2 PV
®
3
RATED OUTPUT POWER @ 120V AC Line:
Stereo mode
4 Ohms, 1 kHz, 1% THD 410 W RMS/chan 630 W RMS/chan 1060 W RMS/chan
8 Ohms, 1 kHz, 1% THD 250 W RMS/chan 370 W RMS/chan 630 W RMS/chan
Bridge mode, mono
8 Ohms, 1 kHz, 1% THD 760 W RMS 1170 W RMS 1900 W RMS
HUM & NOISE:
"A" weighted, reference to rated power @ 8 ohms better than 88 dB
INPUT SENSITIVITY & IMPEDANCE:
@ rated output power, 4 ohms 1.08 V RMS / 2.87dBu 1.17 V RMS / 3.60dBu 1.26 V RMS / 4.23dBu
Balanced, TRS 1/4” phone jack 10 K Ohms per leg 10 K Ohms per leg 10 K Ohms per leg
Balanced, XLR (pin 2 positive) 10 K Ohms per leg 10 K Ohms per leg 10 K Ohms per leg
Overall system gain per channel 40X (+32 dB) 40X (+32 dB) 40X (+32 dB)
DISTORTION: (THD, typical value)
Stereo mode, both channels driven, 4 Ohms
20 Hz to 20 kHz, 10 dB below rated power Less than 0.1%
20 Hz to 2 kHz, at full rated power Less than 0.1%
FREQUENCY RESPONSE:
Stereo mode, both channels driven
+0, -2dB at 1 Watt 12Hz to 35 kHz
DAMPING FACTOR: (Typical value)
Stereo mode, both channels driven
8 Ohms, 20 Hz - 2 kHz > 250:1
POWER CONSUMPTION:
Stereo mode, both channels driven
@ 1/8 rated output power, 4 Ohms 450W 680W 600W
TOPOLOGY: Class AB Class AB
Class G
WEIGHT: 40 lbs (18.2 kg) 45 lbs (20.5 kg) 49 lbs (22.3 kg)
FEATURE SET: All Models (++ indicates each channel)
DDT
COMPRESSION ++: Automatic, switchable with LED indicator
COOLING SYSTEM: Two-speed DC fan, air flow back to front
LOW CUT FILTER ++: -3 dB @ 40 Hz, 12 dB per octave
CROSSOVER ++: 150 Hz, 4-pole Linkwitz-Riley approximation
INPUTS ++: Electronic balanced; Barrier Strip, XLR, TRS 1/4" (6.3 mm)
CROSSOVER OUTPUTS ++: Low/Thru and High, TRS 1/4"Impedance balanced
AMPLIFIER OUTPUTS: Speakons for Chan A, Chan B and Bridge; Binding Posts
LED INDICATORS ++: Red, DDT/clipping; Yellow, signal; Red, Thermal Protect; Green, power
AMP PROTECTION: Full short circuit, open circuit; over-temp thermal; RF; stable into any load
LOAD PROTECTION: Turn on/off muting, DC (triac crowbar), low-cut filter
MAINS VOLTAGES AVAILABLE 100, 120, 230, 240 VAC, 50-60 Hz
DIMENSIONS: Height: 3.5” (8.9 cm), Width: 19" (48.3 cm), Depth: 15.5" (38.0 cm)
Specifications subject to change without notice

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Peavey PV 1 and is the answer not in the manual?

Peavey PV 1 Specifications

General IconGeneral
BrandPeavey
ModelPV 1
CategoryAmplifier
LanguageEnglish

Related product manuals