EasyManuals Logo
Home>Rheem>Furnace>RGRS SERIES

Rheem RGRS SERIES User Manual

Rheem RGRS SERIES
12 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #8 background imageLoading...
Page #8 background image
Air
Accessories
RGRS/RGRT Series
8
UPFLOW ACCESSORIES
FILTER RACK FILTER SIZES* INCHES [mm]
10
19
1
/4 x 25
[489 x 635]
15
3
/4 x 25
[400 x 635]
12
MODEL
RGRS/RGRT-
RXGF-CB
(BOTTOM)
RXGF-CA
(SIDE)
22
3
/4 x 25
[578 x 635]
15
3
/4 x 25
[400 x 635]
04
15
3
/4 x 25
[400 x 635]
15
3
/4 x 25
[400 x 635]
06
15
3
/4 x 25
[400 x 635]
15
3
/4 x 25
[400 x 635]
07EE
15
3
/4 x 25
[400 x 635]
15
3
/4 x 25
[400 x 635]
07EF
19
1
/4 x 25
[489 x 635]
15
3
/4 x 25
[400 x 635]
09
19
1
/4 x 25
[489 x 635]
15
3
/4 x 25
[400 x 635]
FURNACE
WIDTH
IN. [mm]
PLENUM
WIDTH
IN. [mm]
PLENUM ADAPTER
UPFLOW
COIL
PLENUM
14
1
/2 [356] 16
1
/4 [413] RXAA-C171 RXAL-B16BU
14
1
/2 [356] 20
1
/4 [514] RXAA-C172 RXAL-B20BU
17
1
/2 [445] 16
1
/4 [413]
RXAA-C185 RXAL-B16BU
17
1
/2 [445] 20
1
/4 [514] RXAA-C173 RXAL-B20BU
17
1
/2 [445] 21
5
/8 [549] RXAA-C187 RXAL-B21BU
17
1
/2 [445] 25
1
/4 [641]
RXAA-C174 RXAL-B25BU
21
1
/2 [533] 25
1
/4 [641] RXAA-C175 RXAL-B25BU
21
1
/2 [533] 22
1
/4 [565]
RXAA-C176 RXAL-B22BU
24
1
/2 [622] 25
1
/4 [641]
RXAA-C177 RXAL-B25BU
24
1
/2 [622] 21
5
/8 [549] RXAA-C187 RXAL-B21BU
21
1
/2 [533] 21
5
/8 [549] RXAA-C188 RXAL-B21BU
PLENUM DATA FOR A COILS
Plenum adapters are required in some instances for use on upflow
applications when plenum and furnace size do not match.
VENT TERMINATION KITS CONCENTRIC:
HORIZONTAL/VERTICAL =
RXGY-E03A (US & Canadian Installations)
HORIZONTAL TWO PIPE: RXGY-D02, RXGY-D03, RXGY-D04
(US Installations)
RXGY-D02A, RXGY-D03A, RXGY-D04A (Canadian Installations)
RXGY-G02 (US Only)
NEUTRALIZER KIT: RXGY-A01
FOSSIL FUEL KIT: RXPF-F01, RXPF-F02 (TVA)
RETURN AIR PLENUM: RXGR-C17B
RXGR-C21B
RXGR-C24B
EXTERNAL BOTTOM FILTER RACK: RXGF-CB
EXTERNAL SIDE FILTER RACK: RXGF-CA
*Filter racks are shipped without filters.
Filters shipped with furnace may be used or a suitable 1" [25.4 mm] filter.
INTERNAL FILTER RACK FOR BOTTOM
OR SIDE RETURN: RXGF-DA*
Each order contains (1) one box of 10 filter racks supplied
without filters.
*Filters available through PROSTOCK
®
.
RXGP-F03
TWINNING KIT—is for use with Rheem
Value Series
90 Gas Furnaces for
parallel operation requirements.
WARNING: IMPORTANT NOTICE
A SOLID METAL BASE PLATE (SEE TABLE) MUST BE IN PLACE WHEN THE FURNACE IS
INSTALLED WITH SIDE OR REAR AIR RETURN DUCTS. FAILURE TO INSTALL A BASE PLATE
COULD CAUSE PRODUCTS OF COMBUSTION TO BE CIRCULATED INTO THE LIVING SPACE
AND CREATE POTENTIALLY HAZARDOUS CONDITIONS. SOLID BOTTOM IS AVAILABLE
FACTORY INSTALLED WITH OPTION CODE 263.
FURNACE BASE
WIDTH
SOLID BOTTOM BASE
PLATE SIZE
IN. [mm]
KIT NO. PLATE NO.
IN. [mm]
17
1
/2 [445] RXGB-D17 AE-61874-02 15
1
/8 x 23
9
/16 [384 x 598]
21 [533] RXGB-D21 AE-61874-03 18
5
/8 x 23
9
/16 [473 x 598]
24
1
/2 [622] RXGB-D24 AE-61874-04 25
5
/8 x 23
9
/16 [651 x 598]
FOR HIGH ALTITUDES:
*HIGH ALTITUDE KIT:
RXGY-F04 (105 KBTU/H)
RXGY-F05 (120 KBTU/H)
RXGY-F06 (45 KBTU/H/60 KBTU/H/90 KBTU/H)
RXGY-F07 (75 KBTU/H)
*For installations over 5000 ft.
OPTION CODE FOR HIGH ALTITUDE: US & Canada – 278
NOTE: High altitude kits and options do NOT include additional burner orifices.
If a burner orifice change is necessary, they must be ordered through
PROSTOCK
®
. See Installation Instructions for more information.
Option – 278 furnaces are shipped with #51 DMS orifices installed. This is
one drill size smaller than standard furnaces to account for expected average
elevations and heating values typically seen in these areas.
CAUTION: Always follow National Fuel Gas Code (NFGC) guidelines when
converting for high altitudes.
For all installations above 2000 ft. (including all option – 278 models), the
burner orifice size needs to be recalculated and verified. A burner orifice
change may still be required. See Installation Instructions for more
information.
NOTE: For Canadian installations only, an optional derate (manifold gas
pressure reduction) method may be used to adjust the furnace for
altitude. See Installation Instructions for more information. This
optional method may NOT be used for U.S. installations.
[ ] Designates Metric Conversions

Other manuals for Rheem RGRS SERIES

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Rheem RGRS SERIES and is the answer not in the manual?

Rheem RGRS SERIES Specifications

General IconGeneral
BrandRheem
ModelRGRS SERIES
CategoryFurnace
LanguageEnglish

Related product manuals