Roborock Q7 Max User Manual

08
When using the robot for the rst time, follow
it throughout its whole cleaning route and watch for
potential problems. The robot will be able to clean by
itself in future uses.
Note:
After xing the charging dock in place, use
a dry cloth to clean the area where the
Moisture-Proof Mat will be located. Tear o
the double-sided tape at the bottom of the
Moisture-Proof Mat, and stick the mat on
the oor, as shown below.
Notes:
•
Always place the Moisture-Proof Mat on wooden oors.
•
The Moisture-Proof Mat attaches best to smooth surfaces.
•
When necessary, remove the double-sided adhesive
tape slowly to reduce residue glue.
B2
Attach the Moisture-Proof Mat
The robot may not turn on when the battery is
low. In this case, place the robot directly onto the dock
to charge.
Note:
Press and hold the button to power on
the robot. When the power light goes on,
place it on the dock to charge. To maintain
the performance of the high-performance
Power On and Charge the Robot
1. Tidy cables and loose items from the
ground and move any unstable, fragile,
precious, or dangerous items to prevent
personal injury or property damage due
to items becoming tangled in, struck by, or
knocked over by the robot.
2. When using the robot in a raised area,
always use a secure physical barrier to
prevent accidental falls that may result in
personal injury or property damage.
B1-1 More than 0.5m (1.6ft)
B1-2 More than 1.5m (4.9ft)
B1
Position the Charging Dock
Keep the charging dock on a level surface,
at against a wall. Connect the power cable
to the charging dock and tidy cables from
Notes:
•
Allow at least 0.5m (1.6ft) of clearance on each side, and
more than 1.5m (4.9ft) in front of the charging dock.
•
If the power cable hangs vertical to the ground, it may
be caught by the robot, causing the charging dock to
be disconnected.
•
The charging dock indicator is on when the charging
dock is electried, and o when the robot is charging.
•
Do not place the charging dock in places that are
directly exposed to sunlight, or block the location
beacon. Otherwise the robot may not be able to
automatically return to the charging dock.
B3
Mopping
To prevent excessive dirt buildup during rst-time
use, oors should be vacuumed at least three times
before mopping.
Note:
Open the upper cover and take out the unit.
B3-1—Remove the dustbin and water tank
combo unit
the oor. To ensure a better user experience
of the mobile app, place the charging dock
in an area with good WiFi coverage.
lithium-ion rechargeable battery pack, keep
the robot charged.
Reinstall the unit. It will click in place.
B3-3—Reinstall the dustbin and water
tank combo unit
Wet the mop cloth and wring it until it stops
dripping, then slide it along the mop cloth
slot before sticking it rmly in place.
B3-4—Install the mop cloth mount
Only use the ocial Roborock mop cloth.
Note:
Notes:
•
To prevent corrosion or damage, only use the
Roborock branded oor cleaner in the water tank.
•
Do not use hot water as this may cause the tank to deform.
•
When lling the water tank, tilt tank 30° to avoid
wetting the lter.
Remove the water tank stopper, ll the tank
with water, and close it tightly.
B3-2—Fill the water tank
Slide the mount forwards along the bottom
of robot until it clicks in place.
B3-5—Install the mop cloth mount

Roborock Q7 Max Specifications

General

Shape	Round
Product color	White
Number of wheels	3 wheel(s)
Dust container type	-
Brush type	Roller brush & Side brush
Noise level	67 dB
Brush material	Rubber
Navigation type	Mapping
Number of brushes	3
Integrated sensors	Laser
Water tank capacity	0.35 L
Dust capacity (base)	2.5 L
Dust capacity (total)	- L
Self-emptying dust container	Yes
Dust capacity (vacuum cleaner)	0.47 L
Battery capacity	5200 mAh
Suction power	4200 Pa

Weight and Dimensions

Depth	350 mm
Width	353 mm
Height	96.5 mm