Roger Technology R30/803 User Manual

3
EN
3


device.
This installaon manual is intended for qualied personnel only.
ROGER TECHNOLOGY cannot be held responsible for any damage or injury due to improper use or any use other the intended usage indicated in
this manual.
Installaon, electrical connecons and adjustments must be performed by qualied personnel, in accordance with best pracces and in
compliance with applicable regulaons.
Read the instrucons carefully before installing the product. Bad installaon could be dangerous.
Before installing the product, make sure it is in perfect condion: if in doubt, do not use the equipment and contact qualied personnel only.
Do not install the product in explosive areas and atmospheres: the presence of inammable gas or fumes represents a serious safety hazard.
Before installing the motorisaon device, make all the necessary structural modicaons to create safety clearance and to guard or isolate all the
crushing, shearing, trapping and general hazardous areas.
Make sure the exisng structure is up to standard in terms of strength and stability.
ROGER TECHNOLOGY is not responsible for failure to observe Good Working Methods when building the frames to be motorised, or for any
deformaon during use.
The safety devices (photocells, safety edges, emergency stops, etc.) must be installed taking into account: applicable laws and direcves, Good
Working Methods, installaon premises, system operang logic and the forces developed by the motorised door or gate.
The safety devices must protect against crushing, cung, trapping and general danger areas of the motorised door or gate.
The European standards EN 12453 and EN 12455 dene the minimum safety requirements for the operaon of automac doors and gates. In
parcular, these standards require the use of force liming and safety devices (sensing ground plates, photocell barriers, operator detecon
funcon etc.) intended to detect persons or objects in the operang area and prevent collisions in all circumstances.
Where the safety of the installaon is based on an impact force liming system, it is necessary to verify that the characteriscs and performance
of the automaon system are compliant with the requisites of applicable standards and legislaon.
The installer is required to measure impact forces and programme the control unit with appropriate speed and torque values to ensure that the
door or gate remains within the limits dened by the standards EN 12453 and EN 12455.
ROGER TECHNOLOGY declines all responsibility if component parts not compable with safe and correct operaon are ed.
Display the signs required by law to idenfy hazardous areas.
Each installaon must bear a visible indicaon of the data idenfying the motorised door or gate.
An omnipolar disconnecon switch with a contact opening distance of at least 3mm must be ed on the mains supply.
Make sure that upline from the mains power supply there is a residual current circuit breaker that trips at no more than 0.03A and overcurrent
cutout upstream of the electrical system in accordance with best pracces and in compliance with applicable regulaons.
When requested, connect the automaon to an eecve earthing system that complies with current safety standards.
During installaon, maintenance and repair operaons, cut o the power supply before opening the cover to access the electrical parts.
The electronic parts must be handled using earthed anstac conducve arms.
Only use original spare parts for repairing or replacing products.
The installer must supply all informaon concerning the automac, manual and emergency operaon of the motorised door or gate, and must
provide the user with the operang instrucons.
The packaging materials (plasc, polystyrene, etc.) should not be discarded in the environment or le within reach of children, as they are a
potenal source of danger.
Dispose of and recycle the packing components in accordance with the standards in force.
These instrucon must be kept and forwarded to all possible future user of the system.

I the undersigned, as acng legal representave of the manufacturer:

hereby DECLARE that the appliance described hereaer:
Descripon: Sliding gate automaon
Model: serie R30
Is conformant with the legal requisites of the following direcves:
• Direcve 89/336/CEE (EMC Direcve) and subsequent amendments;
• Direcve 73/23/CEE (Low Voltage Direcve) and subsequent amendments;
and that all the standards and/or technical requirements indicated as follows have been applied:
EN 61000-6-3
EN 61000-6-2
EN 60335-1
EN 60335-2-103
Last two gures of year in which marking was applied | 03.
Place: Mogliano V.to Date: 02-01-2003 Signature
ROGER TECHNOLOGY is the exclusive proprietor holder of all rights regarding this publicaon.
ROGER TECHNOLOGY reserves the right to implement any modicaons without prior nocaon. Copying, scanning or any alteraons to this document are
prohibited without express prior authorised from by ROGER TECHNOLOGY.

Roger Technology R30/803 Specifications

General

Brand	Roger Technology
Model	R30/803
Category	Gate Opener
Language	English