EasyManuals Logo
Home>Sanyo>Projector>PLV-Z700

Sanyo PLV-Z700 User Manual

Sanyo PLV-Z700
60 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #28 background imageLoading...
Page #28 background image
28
Press the Point ed buttons to select the Image adj. Menu
and press the Point
8 or OK buttons to access the submenu
items.
1
2
Use the Point ed buttons to select the desired item and
press the Point
8 or OK buttons to access the selected item.
The adjustment bar is displayed.
Image adj. Menu
Press the Point 7 button to decrease the contrast; press the Point
8 button to increase the contrast (from -31 to +31).
Contrast
Press the Point 7 button to decrease the brightness; press the
Point
8 button to increase the brightness (from -31 to +31).
Brightness
Press the Point 7 button to decrease the intensity of the color;
press the Point
8 button to increase the intensity of the color
(from -31 to +31).
Use the Point 7 8 buttons to adjust the tint value to obtain a
proper color balance (from -31 to +31).
Color
Tint
Use the Point 7 8 buttons to select the desired Color temp. level
(High2, High1, Default, Low1, or Low2). Default is based on the
currently set image mode (p.27).
Color temp.
IMAGE ADJ. button
Direct Operation
Press the IMAGE ADJ. button on the remote control to display
the adjustment bar of Image adj. Menu items one at a time and
directly adjust the selected item.
Use the Point
ed buttons to select the desired item and the Point
7 8 buttons to adjust the setting. Press the MENU button after
adjusting.
If you press the OK button after adjusting each item, it will enter
the main menu.
Menu Operation
Remote Control
3
Use the Point 7 8 buttons to adjust the setting values and
press the OK button.
Image mode can be adjusted for each input source and the adjustment is kept until the projector is turned off or the image
mode is changed.
Note:
•TintcannotbeselectedwhenthevideosystemisPAL,SECAM,
PAL-M,orPAL-NinVideoinputorS-videoinput.
•TheImageadj.Menucannotbeoperatedwithoutaninputsignal.
Go on to the next page....
Image Adjustment
Image Mode Adjustment
When Advanced menu is set to Off.
When Advanced menu is set to On.
Brightness Contrast Color Tint Color
temp. Red Green Blue Sharpness
Lamp control Gamma Progressive Noise
reduction Brightness
• • • •
Brightness Contrast Color Tint Color
temp. Red Green Blue Sharpness
Lamp control Gamma Progressive
Noise reduction Iris mode Iris range
Auto black stretch Contrast enhancement
Transient improvement Color management
Dynamic gamma 3D-Y/C Custom gamma
Brightness
• • • •
Note:
•3D-Y/Cmaynotappeardependingontheinput
signal.
Note:
•AboveimageisanexampleofwhentheImage
modeissetto“Natural.”Eachvaluevaries
dependingontheselectedImagemode(p.27).

Other manuals for Sanyo PLV-Z700

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sanyo PLV-Z700 and is the answer not in the manual?

Sanyo PLV-Z700 Specifications

General IconGeneral
Projection technologyLCD
Contrast ratio (typical)-
Resolution1920 x 1080 pixels
Aspect ratio16:9
RS-232 ports1
Dimensions (WxDxH)400 x 346 x 154 mm
Lamp typeUHP
Lamp power165 W
Light source typeLamp
Service life of light source2000 h
Service life of light source (economic mode)3000 h
Serial interface typeRS-232
Component video (YPbPr/YCbCr) in2
Weight and Dimensions IconWeight and Dimensions
Weight7500 g

Related product manuals