Sanyo VWM-950 User Manual

- 5 -
EN
8. Recording Features
•Insert a tape with its record tab into the unit.
F.FWD
8
8
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 4 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED – –
STOP
PLAY
9
9
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 4 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED SP
BSP
SLP
2
2
PROGRAM NUMBER 1
DATE – – / – –
START TIME – – : – –– –
END TIME – – : – –– –
CHANNEL – –
REC SPEED – –
STOP
PLAY
F.FWD
3
3
PROGRAM NUMBER 1
B ONCE
DAILY
WEEKLY
STOP
PLAY
F.FWD
4
4 Select the desired month.
Select the desired day.
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 0 3 MON
START TIME – – : – –– –
END TIME – – : – –– –
CHANNEL – –
REC SPEED – –
F.FWD
F.FWD
STOP
PLAY
1
1
- M E N U -
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
MENU
Select an empty program
number.
Select “ONCE”, “DAILY”
(Mon-Fri), or “WEEKLY”.
F.FWD
STOP
5
5 Select the desired start
time (hour).
Select the
minute.
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 4 MON
START TIME 0 7 : 3 0 – –
END TIME – – : – –– –
CHANNEL – –
REC SPEED – –
F.FWD
F.FWD
STOP
6
6
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 4 MON
START TIME 0 7 : 3 0 PM
END TIME – – : – –– –
CHANNEL – –
REC SPEED – –
AM
B PM
STOP
PLAY
F.FWD
Select “AM” or “PM”.
7
7 Repeat the procedure in steps
5) to 6) to set the end time.
Select the desired channel.
Select the desired recording speed.
10
10 Turn off the VCR
for recording.
• TIMER indicator on the VCR lights up.
C.RESET
EXIT
POWER
Warning: Unauthorized recordings of copyrighted video tapes
may be an infringement of copyright laws.
ANT
IN
OUT
AUDIO
VIDEO
OUT IN
OUT
L
R
IN
ANT
IN
OUT
AUDIO
VIDEO
OUT IN
OUT
L
R
IN
ANT
IN
OUT
AUDIO
VIDEO
OUT IN
OUT
L
R
IN
VIDEO
ANT
IN
OUT
AUDIO
OUT IN
OUT
L
R
IN
Connect
1
2
Connect
1) Insert a pre-recorded tape into the playing VCR.
2) Insert a tape with its record tab into the recording VCR.
3) Press
[SPEED] on the remote control of the recording VCR to select
the desired recording speed (“SP” or “SLP”).
4) Select the “L1” or “L2” position on the recording VCR.
• To use the input jacks on the back of this unit, press
[0], [0], [1] on the
remote control or [CHANNEL ] to select “L1” position.
• To use the input jacks on the front of this unit, press
[0], [0], [2] on the
remote control or [CHANNEL ] to select “L2” position.
5) Press
[REC/OTR] on the recording VCR.
6) Begin playback of the tape in the playing VCR.
7) To stop recording, press
[STOP/EJECT
CC
/
AA
] on the recording VCR,
then stop playback of the tape in the playing VCR.
1) Press the [POWER] to turn on
the power.
2) Press [MENU] to select the
main menu.
3) Press [PLAY
BB
] or [
CC
STOP] to
select “TIMER PROGRAM-
MING”, then press [F.FWD
gg
].
4) Press [PLAY
BB
] or [
CC
STOP] to
select the program number
which you want to check. The
details of the program you
selected will appear on the TV
screen.
• Press [F.FWD
gg
] or
[
hh
REW] to go the digit you
want to change, then press
[PLAY
BB
] or [
CC
STOP] to enter
correct numbers.
• You may cancel the entire pro-
gram by pressing [
hh
REW]
while the program number flash-
es.
5) Press [C.RESET/EXIT] to exit.
6) Press [POWER] to return to
timer stand-by mode.
Hint
Hint
• To go back one step, press [
hh
REW]
(during the steps 3) to 9) ).
• If there is a power failure or the unit has been unplugged for more than 30 sec-
onds, the clock setting and all timer settings will be lost.
• If the tape runs out before the end time, the unit will switch to the Stop mode
immediately, eject the tape and the power will be turned off. The TIMER indicator
will flash.
• If a tape is not in the unit or does not have the record tab, the TIMER indicator
flashes and timer recording cannot be performed. Please insert a recordable tape.
• When all the Timer Recording are completed, the TIMER indicator flashes.
To play or eject the recorded tape, press [POWER] first, and then press
[PLAY
BB
] or [
AA
EJECT].
Press [STOP/EJECT
CC
/
AA
] on the unit.
To cancel a Timer Recording that is in progress
Hint
Hint
• For best results during dubbing, use the VCR’s front panel controls whenever possible. The
remote control might affect the playing VCR’s operation.
• Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are
not recommended.
• You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs.
• “L1” or “L2” is found before the lowest memorized channel (example: CH02).
• "L2" input jacks are on the front of this unit.
Timer Recording Hints for Timer Recording
Copying a Video Tape
• If you have connected the VCR to a cable
box or satellite box as the Connection A
on page 1, select the VCR to channel 3 or
4 (the RF output channel of the VCR).
Then, select the desired channel at the
cable box or satellite box. Leave the cable
box or satellite box on for timer recording.
or
or
or
PLAY
• You can program one
year in advance.
or
PLAY
or
or
or
STOP
or
PLAY
STOP
or
PLAY
(Back of Playing VCR)
(Back of TV)
(Back of Recording VCR*)
RF Cable
(supplied)
*
Front input jacks are also available
Audio/Video Cables
(not supplied)
To Check, Correct or Cancel a
Timer Program
TIMER PROGRAMMING
PROG 12345678
DATE
START TIME
END TIME
CHANNEL
Available program
number flashes.
F.FWD
HJ420UD_EN/SP.QX33 05.1.14 14:06 Page 5

Sanyo VWM-950 Specifications

General

Brand	Sanyo
Model	VWM-950
Category	VCR
Language	English