www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB
|
21
7. Before starting the equipment
m IMPORTANT!
You must fully assemble the appliance before
using it for the rst time!
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage
• Check the device and accessory parts for trans-
port damage. When complaints the dealer must be
informed immediately. Subsequent complaints will
not be accepted
• If possible, store the packaging until the warranty
period has expired
• Read the operating instructions to make yourself
familiar with the device prior to using it.
• Only use original parts for accessories as well as
for wearing and spare parts. Spare parts are avail-
able from your specialized dealer.
• Specify our part numbers as well as the type and
year of construction of the device in your orders.
• Before you connect the equipment to the power
supply make sure the data on the rating plate are
identical to the mains data.
m WARNING!
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, lm and small parts! There is a risk of
swallowing and suffocation!
8. Montage
m WARNING!
Always pull the power plug before making adjust-
ments to the equipment.
Assembling the machine stand (Fig. B-E)
• Place the washer (12) on the axle (11) and insert it
into the holes of the support feet (15)
• Place the sleeve (13) and the wheel (4) on the axle
(11).
• Place the lock nut (14) on the thread and tighten it
with the supplied wrench (a).
• After tightening the lock nut (14), mount the wheel
cap (5) onto the wheel (4). The position is indicated
by the grooves (16).
• Repeat the above steps on the opposite side
(Fig. D).
Residual risks
The machine has been built according to the state of
the art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
• Release the handle button and switch off the ma-
chine prior to any operations.
• Even if you use this electric power tool in accord-
ance to instructions, certain residual risks cannot
be eliminated.
• Remaining hazards can be minimized by following
the instructions in „Safety instructions“, „Intended
Use“ and in the entire operating manual.
• Avoid accidental starts: do not press the start but-
ton while inserting the plug into the socket.
• Use the tool that is recommended in this manual.
In doing so, your machine provides optimal perfor-
mance.
• Hands may never enter the processing zone when
the machine is in operation.
6. Technical data
Dimensions L x W x H 480 x 380 x 910 mm
Blade cylinder Ø 180 mm
Number of blades 2
Collection box capacity 45 l
Transport wheels Ø 175 mm
Weight 10 kg
Branch thickness max Ø 45 mm
Motor 230-240V~ 50Hz
Nominal consumption P1 2400 W
Revolutions max. 4200 1/min
Operating type P40
Subject to technical changes!
Noise levels
Guaranteed sound power level L
WA
106 dB(A)
Measured sound power level L
WA
103,8 db(A)
Measurement uncertainty K 2,46 dB(A)
Sound pressure level L
pA
95,5 dB(A)
Measurement uncertainty K
pA
3 dB(A)
Note: The specied sound levels have been deter-
mined using a standardised test procedure and can
be used to compare different electronic devices. Fur-
thermore, these values can be used to assess in ad-
vance the strain on the user caused by the sound.
To Next Page
Loading...
Need help?
General
