www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
22
|
GB
Cleaner container (9)
Fill the cleaner container with the corresponding
cleaner. The admixture of the cleaning agent can
be regulated by the rotary switch / cleaning agent (7).
Hose reel (Fig. 1)
The hose reel facilitates the space-saving storage of
the high pressure hose (3).
With the aid of the crank handle (2), it is possible to
wind the high pressure hose (3) onto the hose reel.
Important note! In order to use the high pressure
cleaner it is necessary to fully unwind the high pres-
sure hose.
Using the attachments (Fig. 4):
Turbo nozzle (15): For eliminating stubborn dirt.
Nozzles (16): For various cleaning work:
Each nozzle is colour coded and delivers a specic
spray pattern and pressure for a particular clean-
ing job.
The size of the nozzle determines the size of the fan
spray and the pressure out of the nozzle.
0° Nozzle – Red: This nozzle delivers a pinpoint
stream of pressurized water and is extremely pow-
erful. It covers only a small area of cleaning. This
nozzle should only be directed at surfaces that can
withstand high pressure such as metal or concrete.
25° Nozzle – Green: This nozzle delivers a 25 de-
gree spray pattern for intensive cleaning of larger
areas. This nozzle should only be used on areas that
can withstand pressure from this nozzle.
40° Nozzle – White: This nozzle delivers a 40 degree
spray pattern and a less powerful stream of water.
This nozzle can cover a wide area and should be
used for most general cleaning jobs.
Chemical Nozzle – Black: This nozzle is used to ap-
ply special chemicals and cleaning solutions. This
nozzle produces the weakest pressure stream.
Spray bottle (17): For intensive cleaning of smooth
surfaces.
Cleaning brush (18): For surface cleaning.
1-10 m: 1,5 mm
2
10-30 m: 2,5 mm
2
• Plug the mains plug on the power cable into the
mains socket outlet.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection condi-
tions. This means that use of the product at any
freely selectable connection point is not allowed.
• Given unfavorable conditions in the power sup-
ply the product can cause the voltage to uctuate
temporarily.
• The product is intended solely for use at connec-
tion points that
a) do not exceed a maximum permitted supply im-
pedance “Z”, or
b) have a continuous current-carrying capacity of
the mains of at least 100 A per phase.
• As the user, you are required to ensure, in consul-
tation with your electric power company if neces-
sary, that the connection point at which you wish to
operate the product meets one of the two require-
ments, a) or b), named above.
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Motor data - type plate
10. Operation
The equipment consists of an assembly with a pump,
which is encased in a shock absorbing housing. The
equipment comes with a lance and a non-slip gun (for
an optimal working position), whose shape and con-
guration comply with the applicable regulations.
Commissioning (Fig. 1, 4)
Once you have completely assembled the high-pres-
sure cleaner and all connections have been made,
proceed as follows:
Turn on the water supply. Unlock the pistol (13) via
the locking switch (C). Pull back the trigger lever (D)
so that the air in the device can discharge.
Switch on the device by setting the on/o switch (5)
to “ON”. Next, press the trigger lever (D).
To switch o, release the trigger lever (D), and the
device switches to stand-by. The high-pressure
cleaner starts again when you press the trigger le-
ver (D).
To switch o the high-pressure cleaner completely,
set the on/o switch (5) to “OFF”.
To Next Page
Loading...
Need help?
General
