To Next PageTo Next PageTo Previous PageTo Previous Page
What to do if my Scheppach SWP750 Water Pump does not start?
If your Scheppach Water Pump isn't starting, the issue might be due to no mains voltage. Check the mains voltage. Another possible cause is that the float switch does not switch. In this case, move the float switch to a higher position.
Why does my Scheppach SWP750 Water Pump switch off after a short running time?
Your Scheppach Water Pump might be switching off shortly after starting due to a couple of reasons. One reason could be that the motor protection is switching off because of excessive water contamination. If this is the case, pull out the mains plug and clean the pump and shaft. Another reason could be that the water temperature is too high. Make sure to keep the water temperature at or below the maximum of 35°C.
How to improve inadequate pump delivery in Scheppach SWP750 Water Pump?
If your Scheppach Water Pump has inadequate delivery, the pump performance might be reduced due to heavily contaminated and abrasive water. To solve this, clean the pump.
What to do if Scheppach Water Pump does not switch off?
If your Scheppach Water Pump isn't switching off, the float switch might not be able to sink. To fix this, position the pump correctly on the bottom of the shaft.
How to troubleshoot a Scheppach Water Pump that does not start?
If your Scheppach Water Pump doesn't start, the issue might be due to the mains voltage not being applied. Check the mains voltage to ensure it's properly connected. Alternatively, the float switch might not be working. Try moving the float switch to a higher position to see if that resolves the problem.
Why does my Scheppach SWP750 switch off after a short period?
If your Scheppach Water Pump switches off after a short period, it could be due to severely contaminated water causing the motor contactor to disconnect the pump. In this case, pull out the power plug and clean both the pump and the shaft. Another possible reason is that the water temperature is too high, causing the motor contactor to break. Ensure that the water temperature does not exceed 35°C.
What to do if the Scheppach Water Pump flow rate is insufficient?
An insufficient flow rate in your Scheppach Water Pump can be caused by severely contaminated water or additions in the water that produce a grinding effect, which reduces pump performance. To resolve this, clean the pump thoroughly.
Why does my Scheppach SWP750 Water Pump have no discharge?
If your Scheppach Water Pump has no discharge, it might be because the pump capacity is reduced due to heavily soiled and abrasive water. Try cleaning the pump to resolve this issue.
What to do if the Scheppach SWP750 Water Pump does not switch off?
If your Scheppach Water Pump does not switch off, the float switch might be stuck. Make sure to set up the pump correctly on the pit base so the float switch can drop freely.
General| Power | 750 W |
|---|---|
| Max Flow Rate | 15000 l/h |
| Max Head | 8 m |
| Suction Height | 7 m |
| Max Immersion Depth | 7 m |
| Max Grain Size | 35 mm |
| Pump Housing | Plastic |
| Voltage | 230 V |
| Frequency | 50 Hz |
| Hose Connection | 47.8 mm (G 1½) |
| Inlet/Outlet Diameter | 1 1/2 inch |
Explains key safety and operational symbols used in the manual.
Details where the pump is suitable for draining flooded areas.
Lists prohibited uses and operational limitations for safety.
Covers safe usage by different users and general handling.
Details electrical connection safety, cable integrity, and proper grounding.
Instructions for attaching the supporting foot for stability.
Guides on connecting the pump to a pipeline or flexible hose.
Covers float switch installation, positioning, and adjustment.
Details safe electrical connection and warnings about damaged cables.
Outlines general cleaning instructions for the pump.
Specific instructions for cleaning the pump's impeller wheel.
Covers pump maintenance, repairs, and consumables.
