CHAPTER 1. ABOUT FOR EURO
FUNCTION
In this section, it is described about common EURO functions of
ECR.
The DISPLAY/PRINT SAMPLE and PROGRAMMING JOB of each
models are described at the other section.
1. CURRENCY EXCHANGE (Exn) RATE
The CURRENCY EXCHANGE RATE is changed from "4inte-
ger+4decimal" to "3integer+6decimal".
[Programming]
(PGM mode)
Currency Exchange Rate programming
A440/
A450
A460/
A470
A490 A550S
A570/
A610
JOB# 1310 1310 1310 1310 1310
2. New CG of EURO Symbol
• EURO character code = 207
3. DOMESTIC CURRENCY SYMBOL
[Programming]
(SRV mode)
Domestic currency symbol programming
A440/
A450
A460/
A470
A490 A550S
A570/
A610
JOB# 986 915-A 915-A 915-A 915-A
4. FOREIGN (EX1) CURRENCY SYMBOL
• EURO symbol character code is added into the Chatacter Code
Table.
• EURO symbol is used to print the EURO amount.
• ECR can use the EURO symbol character for the domestic cur-
rency symbol or exchange (EX1) currency symbol by below pro-
gramming jobs.
• The selection of foreign currency symbol is supported only for EX1
(EURO) because the EURO is used at EX1 or Domestic currency.
(Notes)
• About Remote Printers and Slip printers
(ER-01RP/02RP/03RP/04RP, EPSON TM-295/300/T85, INDATEC
SLIP etc...):
ECR cannot support to print EURO SYMBOL on Remote Printers
and Slip Printers. The EURO symbol is not printed on them be-
cause they do not have EURO symbol themselves now.
[Programming]
(PGM mode)
Currency symbol for EX1 key programming
A440/
A450
A460/
A470
A490 A550S
A570/
A610
JOB# 2334 2680-F 2680-F 2680-F 2680-F
5. FOREIGN CURRENCY DRAWER
[Programming]
(PGM mode)
Exchange drawer No. programming
A440/
A450
A460/
A470
A490 A550S
A570/
A610
JOB# 2680 2680-E 2680-E 2680-E 2680-E
6. FOREIGN CURRENCY DRAWER OPEN
function
This function is used to open the foreign currency drawer without any
sales entry.
Case of Opening FOREIGN CURRENCY DRAWER
(1) At the timing of issuing receipt after tendering foreign currency
amount.
(2) FOREIGN CURRENCY DRAWER OPEN function (THIS FUNC-
TION)
(3) At the timing of issuing XZ REPORT (included CCD)
[Purpose]
This function is used for opening the foreign currency drawer
when the change due of a transaction is given by foreign currency
just after a transaction.
[Operation]
Key entry sequence
---- EXn ----
[Entry conditions]
Operating modes that allow the entry: REG and MGR modes
(It is not allowed in the VOID mode).
This operation cannot be mixed with other entries such as sales
entry within a transaction, and it cannot be mixed with the non-add
code entry.
[Action]
This operation opens the foreign currency drawer.
This operation is executed only when the foreign currency drawer
is set.
This operation dose not have any counter and totalizer.
7. EX1 amount for TOTAL and CHANGE
• This function is selectable at PGM mode (PRINT or NOT).
If "NOT" is selected, the total is printed as domestic currency.
(Current spec)
If "PRINT" is selected, TOTAL AMOUNT is printed both Domestic
amount and EX1 amount (which is calculated by EX1 RATE).
But, EX1 amount is not printed when SUBTOTAL VOID is exe-
cuted.
[Programming]
(PGM mode)
Printing of EX1 amount for Total and Change
A440/
A450
A460/
A470
A490 A550S
A570/
A610
JOB# 2616-X9-D 2680-A 2680-A 2680-A 2680-A
– 1 –
To Next Page
Loading...
Need help?
General
