Need help?Do you have a question about the Sony STR-GX800ES and is the answer not in the manual?
Explains the 4-channel sound information and center modes provided by the Dolby Pro Logic system.
Details how DSP automatically converts signals for adjustable sound parameters with minimal quality loss.
Describes the adjustable sound fields that simulate various listening environments.
Details the steps for unpacking the receiver and verifying all supplied accessories are present.
Explains how to properly insert batteries into the remote commander for operation.
Details connecting the supplied AM loop antenna and tips for improving reception.
Explains how to connect the FM wire antenna or a 75-ohm coaxial cable.
Important notes regarding power connection, connector insertion, and color-coding for hookups.
Illustrates how to connect audio devices using color-coded jacks for proper channel assignment.
Clarifies the function of TAPE IN jacks for monitoring, not recording.
Shows how to connect video devices, including S-VIDEO and standard video inputs.
Explains the benefits of using S-VIDEO jacks for clearer picture quality.
Provides important notes on S-VIDEO and VIDEO circuitry independence and connection compatibility.
Illustrates speaker cord connections, emphasizing polarity (+/-) for correct sound reproduction.
Guides on setting the impedance selector based on the nominal impedance of connected speakers.
Offers advice on speaker placement to achieve the best surround sound effect.
Details connections for rear speakers, center speakers, and subwoofers using SURROUND OUT jacks.
Describes connecting a subwoofer via line input to the SURROUND OUT MONO jack.
Explains how to activate the low cut filter for front speakers when using a subwoofer.
Illustrates connecting the power cord to the wall outlet and cautions about power consumption.
Warns about total power consumption limits and avoiding high-wattage appliances on the switched outlet.
Explains how to select program sources and adjust volume, muting, balance, and bass boost.
Guides on setting the speaker selector for different speaker configurations and headphone listening.
Details how to adjust volume, mute sound, balance stereo imaging, and use low boost.
Details using SYSTEM CONTROL/FUNCTION buttons and operative buttons for various components.
Describes how the remote controls Sony TVs, including automatic turn-on and input switching.
Explains how to turn on/off the receiver and connected components using the remote.
Details how to operate other components simultaneously while listening to a program source.
Guides on reassigning FUNCTION buttons to control different components or devices.
Explains how to tune into FM/AM stations by directly entering their frequencies using numeric buttons.
Details the process for changing tuning frequencies, including handling non-receivable frequencies.
Offers a solution for FM stereo distortion by switching to monaural mode.
Describes how the receiver automatically scans and locates radio stations.
Guides on storing up to 30 FM/AM stations in memory pages (A, B, C) for easy recall.
Explains how to overwrite an existing preset station with a new one.
Explains how to tune into a stored station by entering its memory page and preset number.
Describes how to scan through preset stations to find the desired one.
Explains how to select video sources (TV, VCR, LD) and set audio playback through the receiver.
Details how to watch a video program while listening to audio from a different source, like a CD.
Provides clarification on the FUNCTION MODE button's behavior and timing for mode selection.
Explains how to activate and select from the receiver's built-in sound field presets.
Explains how to record audio from various sources onto tape, DAT, or MD recorders.
Details the process of recording audio programs onto different media types.
Guides on copying audio from one tape or deck to another using the receiver's dubbing function.
Explains how to record video content from sources like VCR, LD player, or TV onto a video tape.
Details how to record separate audio tracks onto a video tape during the editing process.
Explains how to selectively record audio onto specific parts of a video tape.
Guides on creating custom index names (up to five characters) for preset radio stations.
Lists the available letters and symbols that can be used when creating station index names.
Explains how to easily find desired stations by scanning through indexed presets.
Guides on creating index names for program sources like CD or TAPE for easier identification.
Explains how to replace existing index names with new ones for program sources or stations.
Details how to set the receiver to automatically turn off at a specified time.
Explains the process of programming the remote to control non-Sony devices by learning signals.
Details the steps for programming specific buttons by aligning remotes and transmitting signals.
Informs about the approximate number of signals that can be stored in the remote's memory.
Explains how to clear an existing programmed signal and replace it with a new one.
Details the procedure for clearing previously programmed signals from the remote's memory.
Explains how to set separate amplifier volumes and adjust the overall level with the receiver's volume control.
Explains how Dolby Surround Sound enhances audio experiences with theater-like sound.
Guides on choosing the appropriate center mode (Phantom, Normal, Wide, 3 CH Logic) based on speaker setup.
Explains how to set speaker levels for balanced surround sound using the test tone feature.
Illustrates the sequence of test tone output for different speaker configurations.
Details how to adjust the time difference between front and rear speakers for immersive sound.
Explains how to disable the surround effect and revert to normal sound.
Lists and describes parameters like Room Size, Wall Type, and Reverb Time adjustable for custom sound fields.
Explains how to create personalized sound field settings by adjusting parameters to fit the listening environment.
Details how parameters like Room Size simulation affect sound by controlling early reflections.
Explains the ROOM SIZE parameter and how it simulates different room acoustics.
Explains the WALL TYPE parameter and how it affects high frequencies based on wall material.
Details the SEAT F/R and L/R parameters for adjusting sound based on listening position.
Details adjusting Effect Level, which combines early reflections and reverberation, to change room 'liveness'.
Explains how to adjust the REVERB TIME parameter to control the length of reverberative sound.
Offers a procedure for effectively setting up desired sound fields and adjusting parameters.
Guides on adjusting equalizer bands (bass, middle, treble) and slope for custom sound fields.
Details how to adjust the equalizer slope (Narrow, Mid, Wide) for the middle frequency range.
Explains how to adjust bass and treble sound controls for the STR-GX800ES model.
Explains how to select desired sound fields using the SOUND FIELD ON/OFF and MODE buttons.
Details the procedure to reset custom sound fields and return to the original factory presets.
Lists common issues like tuning failures, stereo indicator problems, and low volume with their causes and solutions.
Addresses issues where no sound is heard, checking connections and selector settings.
Covers problems with rear speaker output, checking sound field and center mode settings.
Explains how to correct reversed speaker connections and ensure proper phase.
Provides solutions for severe hum or noise, including cord shielding and grounding.
Addresses problems with the remote not operating, such as low batteries or obstructions.
Lists power output ratings for front, center, and rear channels under various impedance conditions.
Provides specifications for amplifier section features like dynamic power, frequency response, and input sensitivity.
Details specifications for DSP features like sampling frequency, equalizer, and surround parameters.
Lists specifications for the AM tuner, including frequency range, sensitivity, and S/N ratio.
Provides specifications for the FM tuner, including frequency range, sensitivity, and harmonic distortion.
Shows diagrams of the front panel for STR-GX900ES and STR-GX800ES models with numbered controls.
Explains the power switch, low cut filter indicator, and standby indicator.
Details the DPC MODE button and its indicators for controlling sound processing features.
Describes the FUNCTION knob for source selection and other function-related buttons.
Shows a diagram of the remote control with numbered buttons corresponding to their functions.
Explains the LEARN button for programming the remote to control other devices.
Details the SYSTEM CONTROL/FUNCTION buttons used for selecting program sources.
Step-by-step instructions for directly tuning FM or AM stations by entering frequencies.
Concise guide for tuning and saving stations into memory pages and preset numbers.
Shows methods for tuning preset stations via direct number entry or scan tuning.
Step-by-step instructions for creating index names for preset radio stations.
Guides on selecting stations within an index or from other indexed stations.
Shows how to create index names for program sources other than TUNER.
Step-by-step guide for selecting sound field programs and adjusting sound parameters.
Concise guide for adjusting equalizer slope and level for the STR-GX900ES model.
Step-by-step guide for adjusting tone controls (bass, treble) on the STR-GX800ES model.
To Next Page
General
