TCL 40S5400A Instructions

EN
8
English
Getting started
Important
:
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. Remove batteries when
the remote control is not to be used for a long time. Batteries left in equipment may cause damage through
deterioration and corrosive leakage, invalidating the guarantee.
To protect the environment use local recycling facilities for battery disposal. Dispose of used batteries
according to the instructions.
CAUTION
: Risk of explosion if batteries are replaced by an incorrect type. Replace only with the same or
equivalent type recommended by the equipment manufacturer.
You can turn on the TV from standby mode by pressing the button on your TV set.
While the TV is on, the multi-function menu appears by pressing the button on your TV set. For more
information about how to use the multi-function menu, please refer to the figure below.
Standby
Tips: Click to select options, press and hold to confirm.
Volume+
Source OKVolume-
CH-CH+
• Press the button to move the highlight to the next function selection.
• Press and hold the button for more than 2 seconds to confirm your selection.
Note: Please refer to the Quick Start Guide to nd the button on your TV set.
Switch the TV on and o󰀨
1.
When the power cord is connected, the TV will be turned on directly or be in standby mode. If the TV is in
standby mode, press the or
POWER/
button on the set or the button on the remote control to turn it
on.
2.
To put the TV into standby mode, press the button on the remote control. The TV set remains powered up,
but with low energy consumption.
3.
To switch the TV o󰀨, unplug the mains plug from the mains outlet.
Initial setup
The rst time you switch the set on, the
Welcome
screen appears, which guides you through the initial setup
process. Follow the on-screen instructions to nish the initial setup process such as selecting the language,
connecting to the network, scanning channels, and more. During each step, either make a choice or skip the
step. If you skip a step, you can perform the setup later from the settings menu.
Note: If the channel search retrieved only the analogue channels it could be caused by poor broadcasting and
therefore is not covered by manufacturer warranty. Manufacturers cannot be held responsible for lack of
or poor broadcasting in some areas.

TCL 40S5400A Specifications

General

Screen shape	Flat
LED backlight	Yes
Response time	6.5 ms
Display diagonal	40 \
Display brightness	220 cd/m²
Display technology	LED
Native aspect ratio	16:9
Native refresh rate	60 Hz
Peak luminance ratio	65 %
LED backlighting type	Direct-LED
Contrast ratio (typical)	5000:1
Display diagonal (metric)	101 cm
Motion interpolation technology	PPI (Picture Performance Index) 700
Dynamic contrast ratio marketing name	Mega Contrast
Audio decoders	Dolby Digital, Dolby Digital Plus
RMS rated power	19 W
Built-in subwoofer	No
Number of speakers	2
Audio output channels	2.0 channels
Color name	Dark silver
Stand type	Legs stand
Product color	Silver
Panel mounting interface	100 x 100 mm
AC input voltage	220-240 V
AC input frequency	50/60 Hz
Energy efficiency scale	A to G
Power consumption (standby)	0.5 W
Power consumption (typical)	- W
Package depth	128 mm
Package width	1025 mm
Package height	605 mm
Package weight	7600 g
Pallet width	1200 mm
Pallet height	800 mm
Pallet length	1420 mm
Quantity per truck	396 pc(s)
Quantity per pallet	12 pc(s)
Number of pallets per truck	33 pc(s)
Processor cores	4
Audio formats supported	MP3, WMA
Image formats supported	BMP, JPG, PNG
Video formats supported	AVI, H.264, H.265, MKV, MP4, MPG, OGM, TS, VP9, WMV
Picture processing technology	TCL IPQ 2.0 Engine
High Dynamic Range (HDR) technology	Hybrid Log-Gamma (HLG), High Dynamic Range 10 (HDR10)
HDCP version	2.2
HDMI version	1.4
RF connector type	F, IEC
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN (RJ-45) ports	1
Consumer Electronics Control (CEC)	T-link
Common interface Plus (CI+) version	1.3
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity	0
Tuner type	Analog & digital
Analog signal format system	NTSC, PAL BG, PAL DK, PAL I, PAL L, SECAM B/G, SECAM D/K, SECAM L
Digital signal format system	DVB-C, DVB-S2, DVB-T2
Control type	Buttons, Wireless
Programming period	8 day(s)
Number of OSD languages	29
Firmware upgradeable via	Network, USB
On Screen Display (OSD) languages	ALB, BUL, CRO, CZE, DAN, DEU, DUT, ENG, ESP, EST, FIN, FRE, GRE, HUN, ITA, LAT, LIT, MAC, NOR, POL, POR, RUM, RUS, SER, SLK, SLV, SWE, TUR, UKR
Music apps	Spotify
Video apps	Amazon Prime Video, YouTube, Twitch
Smart modes	Game, Movie, Sports
Sports apps	Red Bull TV
Operating system version	Android R (11.0)
App distribution platform	Google Play
Operating system installed	Android
Hybrid Broadcast Broadband TV (HbbTV) version	2.0.2
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Bluetooth version	5.0
Bluetooth profiles	A2DP, SBC
Remote control type	RC802NU1
Processor	MT5867 / 4x CA55
Internal memory	2800 MB
Cord length	1.5 m
User memory	2.1 GB
Power plug type	Type C
Warranty period	2 year(s)
Processor frequency	1.5 GHz

Weight and Dimensions

Stand depth	186 mm
Stand width	770 mm
Depth (with stand)	184 mm
Width (with stand)	893 mm
Height (with stand)	560 mm
Weight (with stand)	5300 g
Depth (without stand)	90 mm
Height (without stand)	508 mm
Weight (without stand)	5230 g