TCL 55C728 User Manual

6
Chapter 2 Getting Started
Switching On
Follow the instructions on this page on how to switch on your TV set
and the remote control before going on to following pages describing
how to use the channel set-up procedure.
1. Insert two AAA batteries in the remote control.
Precautions on using batteries:
- Only use the battery types specied.
- Make sure you use the correct polarity.
- Do not mix new and used batteries.
- Do not use rechargeable batteries.
- Do not expose batteries to excessive heat such as sunshine,
re or the like, throw them in a re, recharge them or try to open
them, as this could cause them to leak or explode.
- Remove the batteries from the remote control if you are not using
it for a long period of time.
- Attention should be drawn to the environmental aspects of battery
disposal.
2. Connect the power cable FIRST to the television, THEN to a mains
socket. (Note: If the power cable is connected to the television,
please only connect the power cable to the mains socket.)
Your TV set should only be connected to an AC supply. It must not
be connected to a DC supply. If the plug is detached from the ca-
ble, do not, under any circumstances, connect it to a mains socket,
as there is a risk of electric shock.
Note: The gures are for representation only, the location of power
socket of the television may differ depending on the model.
3. Connect an outside aerial to the Antenna/Cable input socket at
the back of the TV set.
The aerial socket (75 OHM - VHF / UHF / cable) can be used for
connecting an external aerial or other equipment tted.
Notes:
- If you want to receive the signal from your cable or cable box,
please connect a coaxial cable to the Antenna/Cable input socket
at the back of the TV set.
- If you want to receive the signal from your satellite receiver, please
connect a coaxial cable to the Satellite input socket at the back of
the TV set.
4. When powered on, the TV will be turned on directly or be in
standby mode.
If the power indicator lights up, the TV set is in standby mode.
Press the
button on the remote control or on the TV set to turn
on the TV.
Switching Off
• To put the TV set into standby mode, press the button on the
remote control. The TV set remains powered up, but with low
energy consumption.
• To switch off the TV set, unplug the mains socket from the mains
outlet.

TCL 55C728 Specifications

General

Screen shape	Flat
Response time	- ms
Display diagonal	55 \
Display brightness	- cd/m²
Display technology	QLED
Native aspect ratio	-
Display diagonal (metric)	139 cm
Dynamic contrast ratio marketing name	Mega Contrast
Power consumption (typical)	- W
Product color	Silver
Panel mounting interface	300 x 300 mm
Package depth	150 mm
Package width	1400 mm
Package height	864 mm
Package weight	19400 g
Processor cores	4
High Dynamic Range (HDR) technology	Dolby Vision IQ, High Dynamic Range 10 (HDR10), High Dynamic Range 10+ (HDR10 Plus), Hybrid Log-Gamma (HLG)
Audio decoders	Dolby Atmos, Dolby Digital AC4, Dolby TrueHD
Video apps	Amazon Prime Video, Netflix, YouTube
Smart modes	Game, Movie, Sports
Operating system installed	Android
Hybrid Broadcast Broadband TV (HbbTV) version	2.0.2
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Bluetooth profiles	A2DP, HID
RF ports quantity	2
USB 2.0 ports quantity	1
Consumer Electronics Control (CEC)	T-link
Common interface Plus (CI+) version	1.4
Tuner type	Analog & digital
Analog signal format system	NTSC, PAL, SECAM
Digital signal format system	DVB-C, DVB-S2, DVB-T2
Repairability index	6.8

Weight and Dimensions

Depth (with stand)	302 mm
Width (with stand)	1227 mm
Height (with stand)	768 mm
Weight (with stand)	14700 g
Depth (without stand)	81 mm
Height (without stand)	712 mm
Weight (without stand)	14400 g