Technics SL-DL5 Service Manual

Remote control jack
Phono output
terminals
Ground
Tonearm drive motor
Record size
detection lever
Record detector
Turntable mat
Phono output terminal
Cabinet switch
Remote controi jack
Turntable drive IC
Operation amplifier IC
Micro computer IC
*The product for destination [XA] is equipped with voltage selector.
™
DISASSEMBLY
INSTRUCTIONS
Voltage selector
(110V — 120V/220V — 240V)
AC input socket
Stylus-pressure
adjustment screw
Cabinet switch
Center spindle
45 rpm adaptor
oe Speed selector
AC input socket
Record size detection
switch
Voltage selector circuit
(Product for [XA] only)
Power transformer
Power source fuse P.C.B.
On/off switch
(Power)
[5]
Hon @
1.
2.
3.
4,
. When putting the turntable mat on the turntable, match
. Remove the bottom board. :
. Release the holder of the stator
. Remove the 2 setscrews (Fig. 4 :
. Remove the 3 setscrews (Fig. 4:
How
to
remove
the
turntable
e
How
to
remove
the
bottom
board
.
Open
the
upper
cabinet.
1.
Remove
the
45
rpm
adaptor
and
turntable.
.
Detach
the
45
rpm
adaptor
as
shown
in
Fig.
1.
2.
Turn
over
the
body
on
a
soft
cloth
taking
care
not
to
.
Remove
the
turntable
mat
and
lift
up
the
turntable.
damage
the
upper
cabinet
and
dust
cover.
*The
turntable
is
tight
fitted
onto
the
center
spindle.
3.
Remove
the
6
setscrews.
(Fig.
3:
@9~@)
When
removing
the
turntable,
take
care
not
to
give
damage
to
the
upper
cabinet
arm
motor
cover
and
e
tonearm cover.
@
the
projection
of
the
turntable
(record
detector)
with
f
the
hold
of
the
turntable
mat.
(See
Fig.
2)
°
oO
Cc
Turn
counterclockwise
Turntable
mat
f
fngulator
and lift up.
! Spring
Record detector
How to remove the main circuit printed board
Remove the bottom board. (Refer to ‘“‘How to remove the bottom board”.)
Release the holder of the stator frame lead connector and pull off the lead wire. (Fig. 4)
Remove
the
6
setscrews
(Fig.
4:
@
~
@)
of
the
printed
circuit
board.
When mounting the printed circuit board.....
(1) Turn the record detecting sensor lever counterclockwise.
(2) Insert the speed selector switch into the knob.
(3)
Connect
the
lead
wire
to
the
connector,
close
the
holder
and
tighten
the
screws.
*The
printed
circuit
board
‘is
grounded
to
the
chassis
by
screw
@
.
When
checking
the
conduction
with
screw
@
removed,
connect
the
earth
terminal
of
the
printed
circuit
board
to
the
chassis
(stator
frame).
How to remove the stator frame
(Refer to “How to remove the
bottom board”.)
Main printed
wa circuit board
frame
sead
connector
and
pull
of
Speed
selector
the
lead
wire.
(Fig.
4)
switch
Turn
C counterclockwise
®
,
®
)
of
the
radiator.
r=
wa Record
ra detector lever
® ~ @) of the stator frame.
F®

Technics SL-DL5 Specifications

General

Brand	Technics
Model	SL-DL5
Category	Turntable
Language	English