Technics ST-610L User Manual

I LOCATIONS
OF
CONTROLS
power
only.
The unit
is in
the
"standby" condition
when
this switch
is
set
to the standby
cb
posilion.
Regardless
oÍ
the switch
setling,
the
primary
circuit
is
always
"live"
as long
as the
power
cord
is connected
to an
electrical
outlet.
Power "standby
Ó/on''
(power/r
standbY
Ó
_
This switch switches
ON
and
switch
on)
oFF the
secondary
circuit
FM
stereo
indicator
(stereo)
This
indicator
automatically
illuminates
when
an FM
stereo
broadcast
is being
received.
Note:
lt
will
not
illuminate
iÍ
the
FM
mode selector
is
set to
the
monaural
mode.
The
lndlcatlon AM used
here lncludes
both MW and LW.
Band
selectors
(band)
FM:
Press this button
to listen to an
FM
broadcast.
MW:
Press
this
button to
listen to an
MW broadcast.
allocatlon:
This
butlon
is
also
used to
select a
Írequency
step
oÍ
either 9
kHz
or
10
kHz.
When
the
MW
button
is
pressed
tor
about
4
seconds,
the
MW
Írequency step
will
change
to
10
kHz
peí
step.
ohis
step
is
set
to 9
kHz beÍore shipment.)
Set
to the appropriate
position
Íot
your
locality.
ln
order lo
return to the original
írequency indica-
tion,
press
this
button
Íor about
4
seconds
a9ain.
LW:
Press.this
button
to
listen
to
an LW broadcast.
íreq shlít:
When
the LW butlon
is
pressed
íor about
4
seconds during reception
oÍ an LW
broadcast,
the LW
írequency
will decrease by 2
kHz.
So, íor example, to
receive
153 kHz'
tune lo
'l55
kHz,
and
then
press
this
button.
]n
order lo
return
to
the original
írequency
indica-
tion,
press
lhis
button
Íor aboul
4
seconds
again.
Digital
írequency
display
The reception
Írequency
oÍ
the
FM
or
AM
broadcast
selected
by
using the tuning
buttons or
the
pÍeset-tun-
ing butlons
is
indicated
by
a
digital-type
display.
Quartz-lock
indicator
(quartz
lock)
This indicator
illuminates
when
tuned
precisely
to
an
FM or AM
station.
Memory
indicator
(El)
This
indicator
illuminates
when
the
memory
butlon
is
pressed.
Channel
display
The channel number
se]ected
by the
pÍeset'
tuning
buttons
is
displayed.
Signal-strength
indicators
(signal
)
These indicators
show
the
relative
strength
oÍ broadcast
signals
being
received
by
the antenna.
The
best condi-
tion
Íor
reception,
íor
FM
and AM'
is
when
the
indicators
illuminate
completely to
the
right.
Tuning buttons
(tuning)
These
buttons
are used
Íor
tuning
to the desired broadcast station.
Memory
button
(memory)
This
button
is
used
when
preset
memory
setting
oí the
preset-tuning
buttons is made.
FM
mode selector
(FM
mode)
This
unit automatically
switches
into
the
stereo
mode
when a steíeo
broadcasl
is
received. Press
this
button
lo
listen
in
the
monaural
mode. The slereo
indicator
will
not
illuminate
in
the
monaural mode.
Preset-tuning
buttons
(1-0)
(24
channel
random
presst
tuning)
These buttons
are used
to
preset
FM
and AM broadcasl
Írequencies
into
the
memoíy
oÍ this unit, arrd are
also
pressed
lo select
the desired
preset
Írequencies.
Note:
Fle'er
to
page
6
íor
inÍormation concerning
presel
memoÍy.

Technics ST-610L Specifications

General

Brand	Technics
Model	ST-610L
Category	Tuner
Language	English