TP-Link TL-SG1005P Wall Mounting Guide

1.1 Wall Mounting Preparation
Before mounting the switch, you need to prepare the tools below:
Ǵ A screw driver.
Ǵ Two screws which complies to the corresponding standard. For details, see Wall
Mounting Specification.
1.2 Wall Mounting Procedure
On the bottom of the panel, there are two mounting holes. You need to drive two screws
into the wall, then mount the switch on the wall. Note that the switch should be mounted
on the wall upright rather than sideways.
1) Determine the location on the wall where you want to mount the switch.
2) Mark the wall where the two mounting holes are. The distance between the two marks
must be the same as that between the two mounting holes of the switch. For the wall-
mounting-holes distance, see Wall Mounting Specification.
3) Drive the screws into the wall at the marks using the screw driver. For the Screw-
Head-to-Wall Minimum Distance, see Wall Mounting Specification.
4) Mount the switch on the wall.
1.3 Wall Mounting Specification
Model
Screw Standard of
ANSI B1.1
Minimum Length
of Screw
Screw-Head-to-Wall
Minimum Distance
Wall-Mounting-Holes
Distance
LS105G 4#, (5#), 6# 7mm 1.5mm 76mm
LS108G 4#, (5#), 6# 7mm 1.5mm 65mm
LS1005G 4#, (5#), 6# 7mm 1.5mm 38mm
LS1008G 4#, (5#), 6# 7mm 1.5mm 48mm
TL-SF1005LP 4#, (5#), 6#, 8# 8.5mm 1.5mm 39mm
TL-SF1005P 4#, (5#), 6#, 8# 8.5mm 1.5mm 39mm
TL-SF1006P 4#, (5#), 6#, 8# 8.5mm 1.5mm 94mm
TL-SF1008LP 4#, (5#), 6#, 8# 8.5mm 1.5mm 105mm
TL-SF1008P 4#, (5#), 6#, 8# 8.5mm 1.5mm 105mm
TL-SF1009P 4#, (5#), 6#, 8# 8.5mm 1.5mm 105mm
TL-SF1016D 4#, (5#), 6# 8.5mm 1.5mm 157.2mm
TL-SG1005LP 4#, (5#), 6#, 8# 8.5mm 1.5mm 39mm
TL-SG1005P
4#, (5#), 6#, 8# 8.5mm 1.5mm 39mm
TL-SG1008D
4# 8mm 2mm 100mm

TP-Link TL-SG1005P Specifications

General

Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	5
10G support	No
Auto MDI/MDI-X	Yes
Networking standards	IEEE 802.1p, IEEE 802.3, IEEE 802.3af, IEEE 802.3u, IEEE 802.3x
Cable types supported	Cat3, Cat4, Cat5, Cat5e, Cat6
Copper ethernet cabling technology	10BASE-T, 100BASE-TX, 1000BASE-T
Total Power over Ethernet (PoE) budget	56 W
Power over Ethernet (PoE) ports quantity	4
Maximum cable length	100 m
Power source	DC/PoE
Input current	1.25 A
DC input voltage	48 V
Power consumption (max)	64.44 W
Forwarding rate	7.44 Mpps
MAC address table	2000 entries
Product color	Black
Switch type	Unmanaged
Heat dissipation	219.87 BTU/h
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 90 %
Package type	Box
Package depth	196 mm
Package width	131 mm
Package height	121 mm
Package weight	800 g
Harmonized System (HS) code	85176990
Sustainability certificates	CE, Federal Communications Commission (FCC), RoHS

Weight and Dimensions

Depth	98 mm
Width	99.8 mm
Height	25 mm