TP-Link TL-SG108 Mounting Guide

1.1 Wall Mounting Preparation
Before mounting the switch, you need to prepare the tools below:
Ǵ A screw driver.
Ǵ Two screws which complies to the corresponding standard. For details, see Wall
Mounting Specification.
1.2 Wall Mounting Procedure
On the bottom of the panel, there are two mounting holes. You need to drive two screws
into the wall, then mount the switch on the wall. Note that the switch should be mounted
on the wall upright rather than sideways. For TL-SF1008P/TL-SF1008LP/TL-SF1009P/
TL-SG1008P, the switch should be mounted with the ports facing downward and the
LEDs facing upward.
1) Determine the location on the wall where you want to mount the switch.
2) Mark the wall where the two mounting holes are. The distance between the two marks
must be the same as that between the two mounting holes of the switch. For the wall-
mounting-holes distance, see Wall Mounting Specification.
3) Drive the screws into the wall at the marks using the screw driver. For the Screw-
Head-to-Wall Minimum Distance, see Wall Mounting Specification.
4) Mount the switch on the wall.
1.3 Wall Mounting Specification
Model
Screw Standard of
ANSI B1.1
Minimum Length
of Screw
Screw-Head-to-Wall
Minimum Distance
Wall-Mounting-Holes
Distance
DS105G
4#, (5#), 6#, 8# 7.5mm
1.5mm 39mm
DS105GE
4#, (5#), 6#
7.5mm
1.5mm 52mm
DS105G-M2 4#, (5#), 6#
7.5mm
1.5mm 52mm
DS105GP
4#, (5#), 6#, 8# 8.5mm
1.5mm 39mm
DS105X 4#, (5#), 6# 7.5mm 1.5mm
150mm
DS106GPP 4#, (5#), 6#, 8# 8.5mm 1.5mm 94mm
DS106P 4#, (5#), 6#, 8# 8.5mm 1.5mm 94mm
DS108G 4#, (5#), 6#, 8# 7.5mm 1.5mm 94mm
DS108GE 4#, (5#), 6# 7.5mm 1.5mm 110mm
DS108G-M2 4#, (5#), 6# 7.5mm 1.5mm 110mm
DS108GP
4#, (5#), 6#, 8#
8.5mm 1.5mm 94mm
DS110GMP 4#, (5#), 6# 8.5mm 1.5mm
150mm

TP-Link TL-SG108 Specifications

General

Jumbo frames	16000
Forwarding rate	11.9 Mpps
MAC address table	4000 entries
Jumbo frames support	Yes
Packet buffer memory	1.5 MB
Maximum data transfer rate	2 Gbit/s
Supported data transfer rates	10/100/1000Mbps
10G support	No
Networking standards	IEEE 802.1p, IEEE 802.3ab, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Packet transfer speed	14880pps/148800pps/1488000pps
Connectivity technology	Wired
Ethernet interface type	Gigabit Ethernet
Switch type	Unmanaged
Power connector	DC-in jack
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	8
Switching protocols	CSMA/CD
Certification	CE, FCC, RoHS
Product color	Black
Rack mounting	-
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 90 %
Package depth	191 mm
Package width	130 mm
Package height	92 mm
Package weight	510 g
Power source	DC
Input current	0.6 A
Input voltage	9 V
Power consumption (max)	3.31 W
Harmonized System (HS) code	85176990

Weight and Dimensions

Depth	101 mm
Width	158 mm
Height	25 mm