Metron TFA Aerobar with SnakeBi
Published – Jul, 2018. ZS207.v0 © Full Speed Ahead
Introduction
Congratulations on your Vision product. Please read these instructions and follow them for correct use. Failure to follow the
warnings and instructions could result in damage to product not covered under warranty, damage to bicycle; or cause an
accident resulting in injury or death. Since specific tools and experience are necessary for proper installation, it is
recommended that the product be installed by a qualified bicycle technician. FSA & Vision assumes no responsibility for
damages or injury related to improperly installed components.
Warranty
Full Speed Ahead (FSA) warrants all FSA, Vision, Metropolis and RPM products to be free from defects in materials or
workmanship for a period of two years after original purchase unless otherwise stated in the full warranty policy. The
warranty is non-transferable and valid to the original purchaser of the product only. Any attempt to modify the product in
any way such as drilling, grinding, and painting will void the warranty. For more information on warranty policy and
instructions for completing a warranty claim, check out the Full Warranty Policy found at our website:
http://www.visiontechusa.com/support/warranty-policy/
Always use a calibrated torque wrench to tighten all screws and bolts when assembling and adjusting the
vision handlebar to the bicycle. Failure to use a calibrated torque wrench can cause damage to the handlebar making it
unsafe to ride and is not covered under warranty. Check bolt and screw torque before each ride to ensure they have not
loosened during use.
Periodically inspect your Aerboars for any cracks, chips, scratches, and any other visible damage. In the
event of an accident do not ride the bicycle until the handlebars have been inspected by an experienced mechanic as the
aerobars may be damaged or weakened even if no visible damage is apparent. If there is any visible damage, the aerobars
should not be used any further and replaced.
When changing the Armrest Stack spacers ⑩, ⑪, ⑫, use the correct length bolt ② as per the chart show in
Table 1. Use only FSA supplied bolts. Failure to use the correct length bolt can result in thread strippage of the base bar,
failure of base bar, and armrest pad and can cause serious accident or injury.
Specification
These instructions are for the installation and adjustment of the following Vision Brand components only:
Item Number / Model Name HB-KO-Si020 / Metron TFA Aerobar with SnakeBite Stem
Components
Follow the assembly order in the illustration:
① Metron TFA Base Bar
② Extension Width Spacer Bolts (M6) x4
③ Conical Bar/Stem Fixing Nut x2
④ Expander Assembly (TH-863-1)
⑤ Stem Body
⑥ Stem Fixing Bolts (M5x16mm) x2
⑦ Compression Cap & Bolt
⑧ Stem Top Plate
⑨ Stem Top Plate Bolt (M3x16mm) x1
Armre⑩ st Stack Spacers (20mm) x6 (AM)
Armrest Stack Spacers (⑪ 10mm) x2 (AM)
⑫ Armrest Stack Spacers (5mm) x2 (AM)
⑬ Lower Angle Adjustment Bracket x2
⑭ Angle Adjustment Grip Nut x2
⑮ Upper Angle Adjustment Bracket x2
⑯ Aero Extension / Armrest Mount (Left & Right)
⑰ Armrest Adjustment Plate (Left & Right)
⑱ Armrest Adjustment Plate Bolts (M5x10mm) x4
⑲ Extension Fixing Bolts (M5x10mm) x2
⑳ Angle Adjustment Bolt (M7x19mm) x2
○
21
Aero Extension Rear Plug x2
○
22
Bridge
○
23
Bridge Fixing Bolts (M4x8mm) x4
○
24
Armrest Pad Plate (Left & Right)
○
25
Armrest Plate Fixing Bolts (M5x10mm) x4
○
26
Armrest Pad (Left & Right)
○
27
Aero Extension (Left & Right)
○
28
Aero Extension Front Plug x2
○
29
Steerer Clamp Bolt (M5x18mm) x2
To Next Page
Need help?
General
