Yealink SIP-T41S Getting Started

Recovery Mode on Yealink IP phones
1
Overview
This guide shows how to use recovery mode to get your phone ready when it fails to start up.
There are two recovery modes:
1. Using TFTP server (not applicable to CP960 IP phones)
2. Using USB flash drive (only applicable to MP54/MP56/MP58/VP59/SIP-T58A/T57W/T54W/
T53W/T53/T48U/T48S/T46U/T46S/T43U/T42U/T42S/T41S/CP920/CP960 IP phones)
Generally, when a Yealink IP phone is powered and connected to the network properly, it will start up
successfully and get ready for you to use. In case, the IP phone is accidentally powered off when
upgrading, the system data in the flash may be damaged and this makes the IP phone fail to start up.
Therefore, we strongly recommend that do not unplug or remove the power when the phone is
updating firmware or configurations.
Getting Started
Before using recovery mode to get the IP phone ready, the following steps are required:
1. Preparing the Firmware and other Resource Files
2. Configuring the HTTP Server, Configuring the TFTP Server or Connecting the USB Flash Drive to the
IP Phone
Preparing the Firmware and other Resource Files
For the firmware and other resource files, you can ask your Yealink reseller.
Different phone models require different resource files to be used for recovery mode. Some just need the
firmware, while others need extra files like “.bin” or “.rfs” in addition to the firmware.
The filename of the firmware used for recovery mode is strictly required. For example, to use recovery
mode on SIP-T46G IP phones, you must rename the firmware file as T46.rom.
For more details about the firmware name and required resource files, refer to the following table:
Phone Model
The Resource Files Required
Description
SIP-T19(P) E2
T19P_E2.rom, T19P_E2.bin, and T19P_E2.rfs
SIP-T21(P) E2
T21P_E2.rom, T21P_E2.bin, and T21P_E2.rfs
SIP-T23P/G
T2x.rom, T2X.bin, and T2X.rfs
SIP-T27G
T27G.rom, T27G.bin, and T27G.rfs
Note: New factory phones
running V86 firmware version no
longer need “.bin” and “.rfs” files.

Yealink SIP-T41S Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Black
Keypad illumination	Yes
Wi-Fi	No
Networking standards	IEEE 802.3af
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
Supported network protocols	SIP v1, SIP v2, LLDP/CDP/DHCP, OpenVPN, IEEE802.1X, IPv6, FTP/TFTP/HTTP/HTTPS
Volume control	Digital
Number of programmable keys	6
Lines quantity	6 lines
Phonebook capacity	1000 entries
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
Input frequency	50/60 Hz
AC adapter input voltage	100 - 240 V
AC adapter output current	1.2 A
AC adapter output voltage	5 V
Display diagonal	2.7 \
Display resolution	192 x 64 pixels
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %
Voice codecs	CNG, G.711Mu, G.711a, G.723.1, G.726, G.729ab, VAD, iLBC
Certification	CE
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	189 mm
Width	212 mm
Height	175 mm
Package depth	223 mm
Package width	246 mm
Package height	120 mm