HEPA 13 OUTLET FILTER
The vacuum cleaners are equipped with outlet lter HEPA
class (High Efciency Particulate Air) H13.
1
The outlet lter HEPA 13 should be replaced when the
lter’s surface is dirty, or in case when the outlet lter’s
replace indicator lamp (14) is turned on (pulsating red
light). Simultaneously with turning on the light of outlet
lter’s replace indicator, the sound signalling of outlet lter’s
replacement is also turned on (so called „Buzzer”), and the
suction power of vacuum cleaner will be reduced (setting 1).
2
In order to replace HEPA 13 lter, lift up the handle of
vacuum cleaner. Then hold the cover of outlet lter (1) at
two outstanding catches, pull strongly the outlet lter’s cover
using your thumbs, and lift it upwards. Put out the outlet
lter’s cover from the vacuum cleaner.
3
Take out the cassette of HEPA 13 lter, replace the waste
cassette with a new one. The HEPA 13 lter makes possible
the efcient usage of vacuum cleaner for ca. 1 year.
4
Put the cover on in following manner: two ledges located
in the lower part of cover should hit the gaps in the casing
of vacuum cleaner, tighten the cover of lter until the back
catches snap on the casing.
INLET FILTER
Release the catch of front cover
●
(15) and open it.
Take out the bag module SAFBAG/dust container
●
„CYKLON” from chamber of vacuum cleaner.
1
Put out the cover of inlet lter together with installed inlet
lter from the guide rails located on back wall of vacuum
cleaner chamber.
2
Take out the inlet lter from the inlet lter cover.
3
Put the new lter into inlet lter cover (28). Pay attention
whether the edges of lter cling closely to the cover of lter.
4
The cover of inlet lter (28) together with installed lter
press home into guide rails to the previous location.
ATTENTION! The damaged inlet lter should be replaced
with a new, genuine manufactured product only.
Put the bag module SAFBAG/dust container “CYKLON”
●
into the chamber of vacuum cleaner. Close the cover
by pressing it until you hear the characteristic sound
(„click”).
NOISE DAMPENING FOAM
1
In order to clean the noise dampening foam (27) lift up
the handle of vacuum cleaner. Then hold the cover of outlet
lter (1) at two outstanding catches, pull strongly the outlet
lter’s cover (1) using your thumbs and lift it upwards.
2
Put out the cover of outlet lter (1) from the vacuum
cleaner. Turn it round and next put out the noise dampening
foam (27) from the cover.
3
In case the noise dampening foam (27) is dirty, there
is an opportunity to wash it with the running water. Before
re-installing remember to dry the foam.
ATTENTION! Due to safety reasons it is disallowed to
put the wet noise dampening foam.
4
Put the washed out noise dampening foam (27) into its
previous location. Put the cover on in following manner: two
ledges located in the lower part of cover should hit the gaps
in the casing of vacuum cleaner, tighten the cover of outlet
lter (1) until the back catches snap on the casing.
SAFBAG dust bag disassembly/assembly
1
The vacuum cleaner is equipped with safety valve located
in chamber of dust container (bag). It opens automatically in
case the total stopping of suction hose or total stopping of
equipment elements connected thereto happened, it opens
also in case the overll of SAFBAG bag/dust container
„CYKLON” happened. One can hear characteristic „whirr”
sound inside the vacuum cleaner after opening the valve.
Opening the safety valve will cause turning on the lamp of
dust bag full indicator of dust bag/dust container „CYKLON”.
2
The light on dust bag/dust container „CYKLON” (10)
full indicator (the sucker or the brush is upraised over the
cleaned surface) informs, that the bag is full and should be
therefore replaced with new one. Moreover, the dust bag/
dust container „CYKLON” full indicator may operate in case
of suction hose stopping or in case of stopping of equipment
elements connected thereto.
3
Switch off the vacuum cleaner by pressing the on/off
button (7) and unplug the appliance.
4
Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
5
Release the front cover fastening (15) and open the cover.
6
Remove the SAFBAG dust bag module from the vacuum
cleaner chamber (25).
7
Shut the SAFBAG bag cover in order to cover the hole of
the soiled bag. While holding the bag plate, bend it upwards
and pull the bag out of the bag catch, guides.
8
Insert the plate of the new dust bag in the tracks of the
SAFBAG dust bag module (25) and slide it until stop. The
direction for inserting the dust bag is indicated by the arrow
on the bag.
Slide the SAFBAG dust bag module together with the
●
installed bag in the tracks located on the side of the
vacuum cleaner chamber. Close the cover by pressing it
until you hear a characteristic click – pay attention not to
trap the dust bag.
ATTENTION! Do not vacuum without SAFBAG bag
module/dust container „CYKLON” installed in the
vacuum cleaner. The lack of SAFBAG bag module/dust
container „CYKLON” disables slamming the upper
cover of the vacuum cleaner.
ZELMER vacuum cleaners are equipped with SAFBAG dust
bags in the amount indicated in the table. It is recommended
to replace the dust bag if:
a) the dust bag full indicator lights up,
E
D
F
G
Downloaded From Vacuum-Manual.com Manuals
To Next Page
Loading...
Need help?
General
