Zircon StudSensor EDGE User Manual

StudSensor
™
EDGE
Stud Finder
The Zircon StudSensor
™
EDGE stud finder finds the
edges of wood and metal studs up to ¾ in. (19 mm)
deep in walls. It features a sleek, high-impact case,
with a patented pinch grip design, and a new
SpotLite
®
Pointer.
1. INSTALLING THE BATTERY
Do not attempt to unscrew
the back of the tool.
Push in the battery door tab at the
bottom of the tool and open the door.
Insert a new 9 V battery, matching the
positive (+) and negative (-) terminals to
the icons printed on the back. Snap the
battery into place and replace the door.
2. IMPORTANT OPERATING TIPS—
PLEASE READ CAREFULLY
•Tool Position: For proper use, always place scanner flat
against the surface before turning on power.
•Power: Press and hold in the Power button
continuously while in use.
•Operation: Move the unit slowly, while keeping it flat
against the wall. Do not rock, tilt, or lift it.
3. TURNING ON/CALIBRATING THE
TOOL AND FINDING A STUD
Place unit flat on wall. Press and hold the Power button.
Do not move the unit until calibration is complete.
When calibration is complete, the green READY light will
illuminate.
If you calibrate over a stud, the unit will beep, and the
lights will flash. Move the unit a few inches (5–6 cm) right
or left, release the Power button, and start over.
Probable Causes Solutions
Situation
•Moveseveralinches(12–13cm)totheleftorrightandstartagain.
•Turnscanneroff,moveoverafewinches(5–6cm),pressPowerbutton,
and start again.
•Onroughsurfaces,placethincardboardonwall,scanningthroughitto
help slide scanner more smoothly.
•Checkforotherstudsequallyspacedtoeitherside(12,16,or24in.
[305,406,or610mm]apart)orthesamestudatseveralplacesdirectly
above or below the first scan area.
•UseCAUTIONwhennailing,sawing,ordrillingintowalls,floors,and
ceilings where these items may exist.
Noindications.
Lights start blinking
and unit beeps
repeatedly.
Detects other objects
besides studs.
Finds more targets
than there should be.
•Nostudsinthatarea.
•Toolwascalibratedoverastud
or on dense part of wall.
•Tooltiltedorliftedduringscan.
•Electricalwiringandmetal/
plastic pipes may be near or
touching back surface of wall.
After calibration is complete,
continue to hold the Power
button and slowly slide the
unit across the surface.
When the top red EDGE light
is lit, the beep sounds, and
the SpotLite
®
Pointer arrow
shines, you have located
the edge of the stud. Mark
this spot.
Continuescanningbeyond
the marked spot until the red
EDGE light turns off. Slide unit
in reverse direction to locate
other edge of stud. Mark this
second spot. The middle of
the stud is centered between
the two marks.
SpotLite
®
Pointer
Stud Edge Groove
Red EDGE Light
Green READY Light
Battery Door Tab
Power Button
Visitwww.zircon.com/supportforthemostcurrentinstructions.
StudSensor, SpotLite, and Zircon are trademarks or registered trademarks of
ZirconCorporation.
4. OPERATING CAUTIONS
Depending on the proximity of electrical wiring or pipes to
the wall surface, the StudSensor
™
EDGE may detect them
inthesamemannerasstuds.Cautionshouldalwaysbe
used when nailing, sawing, or drilling into walls, floors,
and ceilings that may contain these items.
To avoid surprises, remember that studs or joists are
normallyspaced16in.(406mm)or24in.(610mm)apart
andare1½in.(38mm)inwidth.Anythingclosertogether
or a different width may not be a stud, joist, or firebreak.
Always turn off the power when working near
electrical wires.
5. SCANNING DIFFERENT SURFACES
Freshly painted walls: May take one week or longer to
dry after application.
Wallpaper: The StudSensor
™
EDGE functions
normally on walls covered with wallpaper or fabric, unless
the materials are metallic foil, contain metallic fibers, or
are still wet after application.
Lath & plaster: Due to irregularities in plaster thickness,
this tool is not recommended for use on lath & plaster.
The StudSensor
™
EDGE cannot scan for wood studs and
joists through ceramic tile or carpeting and pad.
Note: Sensing depth and accuracy can vary due to
moisture, content of materials, wall texture, and paint.
LIMITED 1 YEAR WARRANTY
ZirconCorporation,(“Zircon”)warrantsthisproducttobefreefromdefectsinmaterialsand
workmanship for one year from the date of purchase. Any in-warranty defective product returned
toZircon*,freightprepaidwithproofofpurchasedateand$5.00tocoverpostageandhandling,
will be repaired or replaced at Zircon’s option. This warranty is limited to the electronic circuitry
and original case of the product and specifically excludes damage caused by abuse, unreasonable
use or neglect. This warranty is in lieu of all other warranties, express or implied, and no other
representations or claims of any nature shall bind or obligate Zircon. Any implied warranties
applicabletothisproductarelimitedtotheoneyearperiodfollowingitspurchase.INNO
EVENTWILLZIRCONBELIABLEFORANYSPECIAL,INCIDENTALORCONSEQUENTIALDAMAGES
RESULTINGFROMPOSSESSION,USEORMALFUNCTIONOFTHISPRODUCT.
In accordance with government regulations, you are advised that: (i) some states do not allow
limitationsonhowlonganimpliedwarrantylastsand/ortheexclusionorlimitationofincidental
orconsequentialdamages,sotheabovelimitationsand/orexclusionsmaynotapplytoyou,and
further. (ii) this warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
Return product freight prepaid with proof of purchase
date(datedsalesreceipt)and$5.00tocoverpostageand
handling, to:
ZirconCorporation
*Attn: Returns Department
1580DellAvenue
Campbell,CA95008-6992USA
Besuretoincludeyournameandreturnaddress.Outof
warranty service and repair, where proof of purchase is
notprovided,shallbereturnedwithrepairschargedC.O.D.
Allow4to6weeksfordelivery.
CustomerService:1-800-245-9265or1-408-963-4550
Monday–Friday,8:00a.m.to5:00p.m.PST
E-mail: info@zircon.com
©2011ZirconCorporation•P/N63071RevD07/11
6. HELPFUL HINTS (See also number 2, IMPORTANT OPERATING TIPS)
FCC Part 15 Class B Registration Warning
ThisdevicecomplieswithPart15ofFCCRules.Operationssubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseharmful
interference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.

Zircon StudSensor EDGE Specifications

General

Brand	Zircon
Model	StudSensor EDGE
Category	Stud Sensor
Language	English