Autonics BEN Series User Manual

A-45
(A)
Photo
electric
sensor
(B)
Fiber
optic
sensor
(C)
Door/Area
sensor
(D)
Proximity
sensor
(E)
Pressure
sensor
(F)
Rotary
encoder
(G)
Connector/
Socket
(H)
Temp.
controller
(I)
SSR/
Power
controller
(J)
Counter
(K)
Timer
(L)
Panel
meter
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
(O)
Sensor
controller
(P)
Switching
mode power
supply
(Q)
Stepper
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
(U)
Other
Amplier Built-in type with Universal voltage
Model BEN10M-TDT BEN5M-MDT BEN3M-PDT BEN300-DDT
Sensing type Through-beam Retroreective
Retroreective
(with polarizing lter)
Diffuse reective
Sensing distance 10m 0.1 to 5m
※
1
0.1 to 3m
※
1
300mm
※
2
Sensing target
Opaque materials of
Min. ø16mm
Opaque materials of Min. ø60mm
Translucent,
Opaque materials
Hysteresis
-
Max. 20% at ratedsetting
distance
Response time Max. 1ms
Response time 12-24VDC ±10%(Ripple P-P: Max. 10%)
Current consumption Max. 50mA
Light source Infrared LED(850nm) Red LED(660nm) Infrared LED(940nm)
Sensitivity adjustment
- Adjustment VR
Operation mode Selectable Light ON or Dark ON by VR
Control output
NPN open collector / PNP open collector simultaneous output
●Load voltage: Max. 30VDC ●Load current: Max. 200mA ●Residual voltage - NPN: Max. 1V, PNP: Max. 2.5V
Protection circuit Reverse polarity protection, Short-circuit protection
Light receiving element Photo IC
Indicator
Operation indicator : Red, Stability indicator : Green
(The red lamp on Emitter of transmitted beam type is for power indication)
Insulation resistance Min. 20MΩ(at 500VDC megger)
Noise resistance ±240V the square wave noise(pulse width: 1㎲) by the noise simulator
Dielectric strength 1000VAC 50/60Hz for 1minute
Vibration 1.5mm amplitude or 300m/s
2
at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 2 hours
Shock 500m/s²(approx. 50G) in each of X, Y, Z directions for 3 times
Environ-
ment
Ambient illumination Sunlight : Max. 11,000㏓Incandescent lamp : Max. 3,000㏓(Receiver illumination)
Ambient temperature -20 to 65℃, storage : -25 to 70℃
Ambient humidity 35 to 85%RH, storage : 35 to 85%RH
Protection IP50(IEC standard)
Material ● Case, Case cover: Heat resistant ABS ● Sensing part: PC(with polarizing lter: PMMA)
Cable
ø5, 4-wire, Length: 2m(Emitter of through-beam type: ø5, 2-wire, Length: 2m)
(AWG22, Core diameter: 0.08mm, Number of cores: 60, Insulator diameter: ø1.25)
Accessory
Individual - Reector(MS-2) -
Common VR adjustment driver, Mounting bracket, Bolts/nuts
Approval
Unit weight Approx. 342g Approx. 200g Approx. 187g
※
1:
The sensing distance is specified with using the MS-2 reflector and same as the MS-4 reflector. Sensing distance is setting range of the
reflector. The sensor can detect under 0.1m
.
※
2: It is for Non-glossy white paper(100×100mm)
※
The temperature or humidity mentioned in Environment indicates a non freezing or condensation environment.
● DC power, Solid state output type
Feature data
Through-beam type
● BEN10M-TFR ● BEN10M-TDT
Parallel shifting characteristic Angle characteristic
Measuring method Data Measuring method Data
Sensing area(cm)
Operation angle θ
L
Emitter
Receiver
ℓ
1
L
θ
Emitter
Receiver
15
10
5
0
100 50 0 -50 -100
Left
Right
Center
ℓ
1
ℓ
1
Sensing distance L (m)
Operation level
Stable operation level
15
10
5
1
0
40° 20° 0 20° 40°
Left
Right
Center
Sensing distance L (m)
Operation level
Stable operation level

Autonics BEN Series Specifications

General

Brand	Autonics
Model	BEN Series
Category	Amplifier
Language	English